MCQ Steel Structures

MCQ Steel Structures

Q1. The minimum pitch for rivets as per IS 800 is:

Q2. The phenomenon of sudden failure in slender compression members is called:

Q3. Which type of connection is preferred for members subjected to dynamic loads?

Q4. The effective length of a compression member with both ends fixed is:

Q5. The connection resisting both shear and axial tension in bolts is:

Q6. Lacing in a built-up column is provided to:

Q7. Which method is commonly used for field welding?

Q8. Which of the following sections is best for a long compression member?

Q9. Which code governs design and construction of steel structures in India?

Q10. Lug angles are used in steel structures to:

Q11. The weakest plane in a fillet weld is along:

Q12. The yield stress of Fe410 grade structural steel is:

Q13. Which of the following stress combinations is used for limit state of collapse?

Q14. The most economical section for a cantilever beam subjected to uniform loading is:

Q15. Which test is carried out on structural steel to assess ductility?

Q16. The plastic modulus of a section is the ratio of:

Q17. In welded connections, intermittent welds are provided when:

Q18. The failure of a tension member due to rupture occurs at:

Q19. As per IS 800, the maximum permissible slenderness ratio for a tension member is:

Q20. The minimum edge distance for bolt holes as per IS 800 is:

Q21. The slenderness ratio of a column is defined as:

Q22. In steel structures, lateral torsional buckling occurs in:

Q23. The minimum thickness of gusset plates as per IS 800 is:

Q24. Lug angles are typically used in:

Q25. The most suitable type of weld for joining thin sheets is:

Q26. The value of partial safety factor for loads as per IS 800 for limit state of strength is:

Q27. Riveted connections are classified based on:

Q28. The standard value of yield stress for Fe250 steel is:

Q29. Which of the following improves lateral stability in steel beams?

Q30. Which welding process uses a continuously fed consumable wire?

Q31. Which type of stress is primarily induced in the flange of an I-section beam under bending?

Q32. The purpose of web stiffeners in steel beams is to:

Q33. In a bolted connection, the failure due to bearing occurs at:

Q34. In steel construction, cleats are used to:

Q35. The most economical beam cross-section for resisting bending is:

Q36. Which of the following is a semi-rigid connection in steel structures?

Q37. The partial safety factor for material strength in steel design (limit state) is:

Q38. Which connection type resists both shear and moment efficiently?

Q39. The typical end condition of a column affecting its effective length is:

Q40. In a tension member with bolted joints, net sectional area is calculated by:

Q41. Which IS code is used for the general construction of steel structures in India?

Q42. The maximum permissible slenderness ratio for a compression member carrying dead load and superimposed load is:

Q43. The minimum edge distance for hand-driven rivets as per IS codes is:

Q44. Which of the following is used to increase the lateral stability of steel columns?

Q45. Bolted connections failing in bearing will primarily show:

Q46. In a welded joint, throat thickness is:

Q47. The yield strength of Fe410 steel grade is:

Q48. The limiting slenderness ratio for members carrying load with wind/seismic forces only is:

Q49. Which type of weld is typically used to join two plates placed edge to edge?

Q50. As per IS 800, the partial safety factor for steel strength is:

Q51. In a steel beam, lateral torsional buckling is prevented by:

Q52. The effective length of a simply supported steel column is:

Q53. The connection formed by placing two plates parallel to each other and welding along their edges is called:

Q54. Which factor majorly influences the slenderness ratio of a steel column?

Q55. For compression members, the slenderness ratio should generally not exceed:

Q56. In welded connections, intermittent welds are generally used for:

Q57. The term 'block shear failure' in tension members refers to:

Q58. What is the most effective shape for resisting torsion in steel members?

Q59. In steel construction, 'gusset plates' are primarily used for:

Q60. Fillet weld size is governed by:

Q61. The type of bolt commonly used in steel structures where repeated load reversal occurs is:

Q62. As per IS 800, the partial safety factor for load combinations involving wind/seismic forces is:

Q63. When a plate girder is subjected to large shear forces, it is economical to:

Q64. Weld symbol positioned on the continuous line in a welding drawing represents:

Q65. The most effective connection type for transferring axial tension in a steel tie member is:

Steel Structure Design

📖 Design of Tension Members (IS 800:2007, Clause 6)

Design Strength due to Yielding of Gross Section

$$ T_{dg} = \frac{A_g f_y}{\gamma_{m0}} $$

Where:
\( A_g \) = Gross cross-sectional area (mm²)
\( f_y \) = Yield stress of steel (N/mm²)
\( \gamma_{m0} \) = Partial safety factor against yielding (1.10)

Design Strength due to Rupture of Net Section

$$ T_{dn} = \frac{0.9 A_{nc} f_u}{\gamma_{m1}} + \frac{\beta A_{go} f_y}{\gamma_{m0}} $$

Where:
\( A_{nc} \) = Net area of connected leg (mm²)
\( A_{go} \) = Gross area of outstanding leg (mm²)
\( f_u \) = Ultimate tensile stress (N/mm²)
\( \gamma_{m1} \) = Partial safety factor against ultimate stress (1.25)
\( \beta \) = Reduction factor for shear lag

Design Strength due to Block Shear

$$ T_{db1} = \frac{A_{vg} f_y}{\sqrt{3} \gamma_{m0}} + \frac{0.9 A_{tn} f_u}{\gamma_{m1}} $$

$$ T_{db2} = \frac{0.9 A_{vn} f_u}{\sqrt{3} \gamma_{m1}} + \frac{A_{tg} f_y}{\gamma_{m0}} $$

Where:
\( T_{db} \) = Minimum of \( T_{db1} \) and \( T_{db2} \)
\( A_{vg}, A_{vn} \) = Gross and net shear area (mm²)
\( A_{tg}, A_{tn} \) = Gross and net tension area (mm²)

📖 Design of Compression Members (IS 800:2007, Clause 7)

Design Compressive Strength

$$ P_d = A_e f_{cd} $$

Where:
\( A_e \) = Effective cross-sectional area (mm²)
\( f_{cd} \) = Design compressive stress (N/mm²)

Design Compressive Stress

$$ f_{cd} = \frac{f_y / \gamma_{m0}}{\phi + [\phi^2 - \lambda^2]^{0.5}} \le \frac{f_y}{\gamma_{m0}} $$

$$ \phi = 0.5 \left[ 1 + \alpha (\lambda - 0.2) + \lambda^2 \right] $$

Where:
\( \lambda \) = Non-dimensional effective slenderness ratio \( = \sqrt{\frac{f_y}{f_{cc}}} \)
\( f_{cc} \) = Euler buckling stress \( = \frac{\pi^2 E}{(KL/r)^2} \)
\( \alpha \) = Imperfection factor corresponding to buckling class

📖 Design of Flexural Members (IS 800:2007, Clause 8)

Design Bending Strength (Plastic / Compact Section)

$$ M_d = \beta_b Z_p \frac{f_y}{\gamma_{m0}} $$

Where:
\( \beta_b \) = 1.0 for plastic and compact sections
\( Z_p \) = Plastic section modulus (mm³)

Design Shear Strength

$$ V_d = \frac{A_v f_{yw}}{\sqrt{3} \gamma_{m0}} $$

Where:
\( A_v \) = Shear area (mm²)
\( f_{yw} \) = Yield stress of the web (N/mm²)

📖 Bolted Connections (IS 800:2007, Clause 10.3)

Nominal Shear Capacity of Bolt

$$ V_{nsb} = \frac{f_{ub}}{\sqrt{3}} \left( n_n A_{nb} + n_s A_{sb} \right) $$

Where:
\( f_{ub} \) = Ultimate tensile strength of bolt (N/mm²)
\( n_n \) = Number of shear planes with threads intercepting
\( n_s \) = Number of shear planes without threads intercepting
\( A_{nb} \) = Net shear area of bolt at threads (mm²)
\( A_{sb} \) = Shank area of bolt (mm²)

Nominal Bearing Capacity of Bolt

$$ V_{npb} = 2.5 k_b d t f_u $$

Where:
\( k_b \) = Smallest of \( \left( \frac{e}{3d_0}, \frac{p}{3d_0} - 0.25, \frac{f_{ub}}{f_u}, 1.0 \right) \)
\( d \) = Nominal diameter of bolt (mm)
\( t \) = Thickness of connected plate (mm)
\( f_u \) = Ultimate tensile stress of plate (N/mm²)
\( e, p \) = Edge and pitch distance (mm)
\( d_0 \) = Diameter of bolt hole (mm)

Gusset Plates & Detailed Connections

📖 Gusset Plate Design (IS 800:2007, Clause 7.5)

Effective Length of Gusset Plate for Compression (Whitmore’s Section)

$$ L_w = b_c + 2 \cdot L_{conn} \cdot \tan(30^\circ) $$

Where:
\( L_w \) = Effective width at Whitmore dispersion section (mm)
\( b_c \) = Width of connection (e.g., width of member connected) (mm)
\( L_{conn} \) = Length of connection along the gusset (mm)

Compressive Strength of Gusset Plate

$$ P_{dg} = L_w \cdot t_g \cdot f_{cd} $$

Where:
\( t_g \) = Thickness of gusset plate (mm)
\( f_{cd} \) = Design compressive stress based on slenderness ratio of gusset plate (N/mm²)

📖 High Strength Friction Grip (HSFG) Bolts (IS 800:2007, Clause 10.6)

Design Shear Capacity of HSFG Bolt (Slip Resistance at Limit State)

$$ V_{dsf} = \frac{\mu_f n_e K_h F_{0}}{\gamma_{mf}} $$

Where:
\( \mu_f \) = Coefficient of friction (slip factor, typically 0.48 for clean steel surfaces)
\( n_e \) = Number of effective interfaces resisting slip
\( K_h \) = 1.0 for bolts in holes with nominal clearance, 0.85 for oversized/slotted holes
\( F_0 \) = Minimum bolt tension (Proof load) \( = 0.7 A_{sb} f_{ub} \)
\( \gamma_{mf} \) = Partial safety factor for friction grip bolts (1.10 for friction type at ultimate load, 1.25 at service load)

📖 Welded Connections (IS 800:2007, Clause 10.5)

Design Strength of Fillet Weld

$$ P_wd = \frac{f_u / \sqrt{3}}{\gamma_{mw}} t_t $$

Where:
\( f_u \) = Ultimate tensile stress of the smaller of the connected members (N/mm²)
\( \gamma_{mw} \) = Partial safety factor for welds (1.25 for shop weld, 1.50 for field weld)
\( t_t \) = Throat thickness \( = k \cdot s \)
\( k \) = Constant depending on angle between fusion faces (e.g., 0.7 for $90^\circ$ angle)
\( s \) = Size of the fillet weld (mm)

📖 Column Bases & Footings (IS 800:2007, Clause 7.4)

Thickness of Slab Base Plate

$$ t_s = \sqrt{\frac{2.5 w \left( a^2 - 0.3 b^2 \right) \gamma_{m0}}{f_y}} \ge t_{min} $$

Where:
\( w \) = Intensity of upward pressure from concrete foundation (N/mm²)
\( a, b \) = Projections of the base plate beyond the column flange / web (mm)
\( f_y \) = Yield stress of the base plate material (N/mm²)

📖 Effective Length & Slenderness (IS 800:2007)

Slenderness Ratio

$$ \lambda = \frac{KL}{r} $$

Where:
\( KL \) = Effective length of member (mm)
\( r \) = Least radius of gyration of the section (mm)

Recommended Effective Length Factors (\(K\))

End Conditions\(K\)Effective Length
Both ends hinged (pinned)1.0\(1.0L\)
Both ends fixed0.65 (≈0.5 theoretical)\(0.65L\) (code) / \(0.5L\) (ideal)
One end fixed, one hinged0.80\(0.80L\)
One end fixed, one free (cantilever)2.0\(2.0L\)

IS 800 Table 11 gives recommended design values that include partial fixity effects; pure theoretical Euler values are 0.5, 0.7, 1.0, 2.0.

Maximum Slenderness Ratio Limits (IS 800)

  • Compression members carrying DL + imposed load: \(\lambda \le 180\)
  • Members carrying wind or seismic loads only (besides DL): \(\lambda \le 250\)
  • Tension members (to avoid vibration / handling issues): \(\lambda \le 350\) (generally); up to 400 for members not pre-tensioned
  • Lacing bars in columns: \(\lambda \le 145\)
📖 Bolt & Rivet Spacing Rules (IS 800)

Minimum Pitch

$$ p_{\min} = 2.5\,d $$

where \(d\) = nominal diameter of bolt/rivet.

Maximum Pitch

  • In tension: \(p_{\max} = 16t\) or 200 mm, whichever is less
  • In compression: \(p_{\max} = 12t\) or 200 mm, whichever is less

(\(t\) = thickness of thinner plate)

Minimum Edge / End Distance

  • Sheared or hand-flame cut edges: \(1.7\,d_0\) (or 1.5\(d_0\) for machine-flame / sawn / planed edges)
  • \(d_0\) = diameter of the hole

For rivets, older practice often used 1.5–3 times hole diameter depending on driving method; modern design follows the bolt edge-distance rules of IS 800.

📖 Partial Safety Factors (IS 800:2007 Summary)
ItemSymbolValue
Material – yield / buckling\(\gamma_{m0}\)1.10
Material – ultimate / rupture\(\gamma_{m1}\)1.25
Shop weld\(\gamma_{mw}\)1.25
Field weld\(\gamma_{mw}\)1.50
HSFG friction (ultimate)\(\gamma_{mf}\)1.10
HSFG friction (serviceability)\(\gamma_{mf}\)1.25
DL + LL (strength)—1.5
DL + LL + WL/EQ—1.2 (on WL/EQ terms often combined)
📖 Lateral-Torsional Buckling & Plastic Section Properties

Plastic Modulus

$$ Z_p = \frac{M_p}{f_y} $$

where \(M_p\) is the plastic moment capacity of the cross-section. Plastic modulus is larger than the elastic section modulus \(Z_e\); shape factor \(f = Z_p/Z_e\) is typically ≈1.12–1.15 for I-sections.

Lateral-Torsional Buckling (LTB)

Occurs in beams bent about the major axis when the compression flange is free to displace laterally and rotate. Resistance is increased by:

  • Providing lateral restraints to the compression flange
  • Reducing the unrestrained length
  • Using sections with higher torsional and warping stiffness (e.g., closed sections)

Design bending strength is reduced by a reduction factor \(\chi_{LT}\) when LTB governs (IS 800 Cl. 8.2.2).

📖 Built-up Columns – Lacing & Battens

Lacing (or battens) hold the main components of a built-up column in position so that they act together and the individual members do not buckle independently.

  • Lacing systems may be single or double; angle of lacing with axis of member between 40° and 70°.
  • Lacing bars designed for a transverse shear of 2.5 % of axial force in the member.
  • Slenderness of lacing bars \(\le 145\); of main components between lacing connections \(\le 50\).
📖 Weld Types & Throat Thickness

Fillet weld – joins overlapping or T-joints; size \(s\) limited by thickness of thinner part. Throat thickness:

$$ t_t = 0.70\,s \quad (90^\circ\text{ fillet}) $$

Butt weld – joins plates placed edge-to-edge; full-penetration butt welds develop the full strength of the parent metal and are preferred for pure tension transfer.

Spot / plug / slot welds – used mainly for thin sheets or secondary connections.

Weakest plane of a fillet weld is along the throat. Intermittent welds reduce heat input and cost on long joints but must satisfy maximum gap rules of IS 800.

📖 Steel Grades & Material Properties
Grade\(f_y\) (MPa)\(f_u\) (MPa) typical
Fe 250 / E250250410
Fe 410 / E410250–410*410–540
Fe 490 / E450350–450490

*Yield stress of Fe 410 depends on thickness (IS 2062); for thinner sections \(f_y\) is often taken as 250 MPa while ultimate is 410 MPa. Always check the actual product standard.

Ductility is assessed by percentage elongation in the tensile test.

📖 Lug Angles, Cleats & Gusset Notes

Lug angles – short angles attached to the outstanding leg of a tension member to reduce eccentricity and to transfer force more uniformly into the gusset; used mainly with single-angle tension members.

Cleats – angle or plate connectors used to join secondary beams to main beams (simple shear connections).

Gusset plates – connect two or more members at a joint (truss nodes, bracing intersections). Minimum thickness generally 6 mm (IS 800). Whitmore section is used to check compression in the gusset.

📖 Preferred Sections & Failure Modes
  • Long compression members – circular hollow sections (CHS) give high and equal radius of gyration in all directions → excellent buckling resistance.
  • Beams under bending – I-sections concentrate material in flanges far from neutral axis → high section modulus for given weight.
  • Torsion – closed sections (CHS, RHS) far superior to open sections.
  • Block shear – simultaneous shear failure along a row of bolts and tensile rupture beyond the end bolt; capacity is the lesser of the two IS 800 expressions already given above.
  • Bearing failure of bolted joints appears as elongation of the hole in the plate.
Yogendra Gopal Borse

Yogendra Gopal Borse

Civil Engineer | Assistant Engineer Grade-I, Maharashtra PWD

B.Tech (Civil) from VJTI Mumbai. Experienced in bridge design, road works, estimation, project monitoring and digital engineering tools. Creator of YogiPWD – practical technical resources for civil engineers.

Read full About →