IRC:112 Transverse Deck Analysis

IRC:112 Transverse Deck Studio

Analyze and design a one-way transverse deck strip spanning over longitudinal girder support lines. Sweep a user-defined wheel set across the deck, calculate a basic ULS moment envelope, and estimate main and secondary reinforcement using the IRC:112 concrete stress block provisions.

1 · Deck geometry and materials

A uniform 1 m longitudinal strip, continuous over vertical supports at girder centre-lines. Overhangs are modeled as cantilevers.

This version implements the IRC:112 rectangular block for fck ≤ 60 MPa.
Confirm exposure class, durability and construction tolerance.
Surfacing, utilities etc.; exclude slab self-weight.
Tool applies P × (1 + value/100); don’t enter impact twice.
Converts each wheel load into force per metre of bridge length.
Refine and compare envelopes for mesh sensitivity.
Load input boundary: enter wheel loads and offsets taken from the governing IRC:6 vehicle/load arrangement for one critical axle line. Select γG, γQ, impact and edge clearance for the project's applicable combination and carriageway. The tool does not generate IRC:6 vehicle classes, lane placement, multi-lane factors or load combinations.

2 · Critical axle wheel template

Offset is relative to the template origin. Add one row per tire line in the transverse direction; input characteristic load per tire, in kN.

Offset from origin (m)Wheel load (kN)

3 · Results

Enter project load factors, impact allowance, load-spread length, edge clearance and wheel loads, then run the analysis.

Transverse moment envelope

Positive values are sagging; negative values are hogging. This is a linear elastic beam-strip envelope, not a shell finite-element contour or a longitudinal bridge envelope.

Calculation log

No calculation yet.

What the tool models

The model is a one-way, Euler–Bernoulli beam strip of 1 m width along the bridge. Its transverse coordinate runs across the deck. The strip is continuous through vertical support points located at evenly spaced girder centre-lines, with free cantilever overhangs outside the outer girders. It assumes constant gross-strip flexural stiffness across the width; because that stiffness is uniform, its magnitude cancels from this linear load-distribution solution.

For each lateral position of the entered wheel set, the program assembles a beam finite-element stiffness matrix, applies permanent pressure and equivalent point-wheel forces, solves vertical deflections/rotations, and recovers signed bending moments and shear. It searches wheel-set position in the configured increments and forms the envelope. The maximum positive and negative design moments are then used for bottom and top main steel respectively.

Use workflow

  1. Enter the deck width, girder count and overhang. The girder lines are equally spaced between the two overhang limits.
  2. Enter slab thickness, fck, fyk, cover, main bar diameter, unit weight and superimposed permanent load.
  3. From the applicable IRC:6 vehicle and project carriageway arrangement, identify a critical axle’s transverse tire-line offsets and characteristic tire loads. Enter those as the wheel template.
  4. Determine the strip’s longitudinal load-sharing width from an accepted deck analysis or engineer-approved method. Enter it so the wheel load is converted to force per metre of bridge length.
  5. Enter the project’s ULS action factors, dynamic/impact allowance and allowable wheel-edge clearance. The tool applies impact once to the traffic load.
  6. Run the analysis; review moment/shear envelopes, selected reinforcement, minimum steel, bar spacing, shear screen, deflection screen and calculation log.
  7. Repeat with finer mesh and smaller wheel-position increments. Compare the critical response. Then verify with a 2D plate/shell or grillage model and independent calculations.

IRC:112 reinforcement calculation included

For basic ULS, the design values use γc = 1.5, γs = 1.15 and fcd = 0.67 fck / γc. The section resistance calculation uses the Annex A-2 rectangular stress block for fck ≤ 60 MPa (λ = 0.8, η = 1.0), and the simplified bilinear reinforcement law. It solves force equilibrium and checks moment resistance for each trial steel area. It sizes required flexural steel by solving section force equilibrium and moment resistance; top and bottom bars are designed separately. Minimum main steel uses max[0.26 fctm/fyk, 0.0013] btd with fctm = 0.259 fck^(2/3) for this strength range. One-way slab secondary steel is taken as at least 20% of the main reinforcement. Principal spacing is limited to min(2h, 250 mm); secondary spacing to min(3h, 400 mm), in accordance with IRC:112 Clause 16.6.1.1.

What it does not verify

  • It does not select IRC:6 vehicle class, load train, multi-lane arrangements, impact factors, combination factors, lane reductions, braking, fatigue or construction loading.
  • It analyzes one axle-line template at a time in the transverse direction. Axle positions and longitudinal influence effects require separate load cases/analysis.
  • It is not a plate/shell model: no two-way slab action, transverse load spreading through slab depth, wheel contact patch, girder flange width, local support bearing width, torsion, skew, curvature, diaphragms, barriers, edge beams, deck openings or composite girder stiffness.
  • It reports an elastic gross-section deflection only; it does not perform IRC:112 cracked-section SLS, crack-width, stress, fatigue, durability, punching/local wheel shear, anchorage, development length, curtailment, edge stiffening or detailing checks.
  • The shear comparison is an unreinforced concrete screening check at the strip shear envelope. Verify the design section location relative to the bearing face, support width, load dispersion, effective longitudinal width and full IRC:112 shear provisions. A failed screen needs detailed design; a pass is not a complete shear verification.
  • It is not valid for skew/curved/voided/orthotropic slabs, solid slab bridges with significant two-way response, staged construction, prestressed decks, or irregular girder spacing without an appropriate validated analysis model.
Engineering boundary: this is a preliminary strip-analysis aid. A qualified bridge engineer must verify the IRC:6 actions, analysis idealization, all ULS/SLS/fatigue/durability/detailing requirements, and the complete deck–girder system under the adopted code editions and amendments before design use.

Code and research references

Research check date: 28 October 2026. Use the bridge authority’s contract editions, current official amendments and project-specific design criteria.

  • IRC:112-2020, Code of Practice for Concrete Road Bridges (First Revision): Section 7.6.2 allows rational established methods for slab bridge/deck analysis; Sections 8–10 cover ULS section/shear/punching; Sections 12, 14–16 cover serviceability, durability and detailing. The tool references Annex A-2 rectangular stress block (λ=0.8, η=1.0 through fck 60 MPa), Table 6.5 Ecm, Clause 16.5.1.1 minimum steel and Clause 16.6.1.1 slab reinforcement spacing/secondary steel. IRC:112-2020 text copy; confirm against the official purchased publication and notifications.
  • IRC amendments: IRC’s register lists Amendment No. 7 to IRC:112-2020 in 2024; a draft amendment was open for comments through 18 November 2026. Draft text is not adopted unless formally notified. Check the IRC amendment/errata register and current draft documents page.
  • IRC:6-2017, Section II — Loads and Load Combinations: use for the selected traffic class/vehicle wheel arrangement, vehicle positioning, impact and action combinations. The wheel template, edge clearance and factors in this tool are user-controlled, not code-generated. Check official IRC notices and contract requirements.
  • IRC:SP:105, Explanatory Handbook to IRC:112: companion explanatory material with design examples; the IRC catalogue lists it. IRC updated catalogue (2026).

Technical papers supporting the modeling cautions

  • Mabsout, M., Tarhini, K., Jabakhanji, R. & Awwad, E. (2004), “Wheel Load Distribution in Simply Supported Concrete Slab Bridges,” Journal of Bridge Engineering 9(2). Parametric FEM study on wheel-load distribution, span, deck width and shoulders. DOI.
  • Lantsoght, E. O. L., de Boer, A., van der Veen, C. & Walraven, J. (2014), “Effective Width in Shear of Reinforced Concrete Solid Slab Bridges under Wheel Loads.” Experimental slab-strip work on wheel-load spread and shear distribution; supports treating local shear as a separate verification. Open paper copy.
  • Rajchel, M. & Siwowski, T. (2017), “Live load transverse distribution in a road slab-girder bridge made of FRP composite girders,” Roads and Bridges 16(2). Compares analytical and FEM distribution with bridge load-test measurements. DOI.
  • Scordelis, A. C., Samarzich, W. & Pirtz, D. (1960), “Load Distribution on a Prestressed Concrete Slab Bridge,” PCI Journal 5(2), 18–33. Full-scale experimental and analytical transverse wheel-load distribution study. DOI.

These studies explain model sensitivity and validation practice. They are not substitutes for IRC load rules or project-specific analysis.

IRC:112 Transverse Deck Studio · One-way strip analysis · Preliminary engineering aid only
Yogendra Gopal Borse

Yogendra Gopal Borse

Civil Engineer | Assistant Engineer Grade-I, Maharashtra PWD

B.Tech (Civil) from VJTI Mumbai. Experienced in bridge design, road works, estimation, project monitoring and digital engineering tools. Creator of YogiPWD – practical technical resources for civil engineers.

Read full About →