MCQ Fluid Mechanics

MCQ fluid mechanics

Q1. The SI unit of viscosity is:

Q2. A fluid which has no viscosity is called:

Q3. The ratio of inertial force to viscous force is known as:

Q4. Bernoulli’s equation is based on the conservation of:

Q5. The dimension of pressure is:

Q6. Which device is used to measure the flow rate of a liquid in a pipe?

Q7. In fluid mechanics, continuity equation is derived from conservation of:

Q8. Which type of flow has Reynolds number less than 2000?

Q9. Pascal’s law states that pressure at a point in a fluid is:

Q10. The device used to measure atmospheric pressure is:

Q16. The property of a fluid which enables it to resist tensile stress is:

Q17. A streamline is a line which is:

Q18. Which of the following has the highest bulk modulus?

Q19. In dimensional analysis, which of these is a derived dimension?

Q20. Which of the following is used to measure small pressure differences?

Q21. Specific gravity is the ratio of:

Q22. Critical velocity occurs when:

Q23. Hydraulic grade line represents:

Q24. Cavitation in pumps occurs when:

Q25. Mach number is defined as:

Q26. The center of pressure on a plane surface immersed vertically in a liquid lies:

Q27. Hydraulic jump is a phenomenon seen in:

Q28. A venturimeter works on the principle of:

Q29. Specific speed of a pump is defined as speed of a geometrically similar pump that would deliver unit discharge at:

Q30. Bernoulli’s equation can be applied between two points in a fluid flow when:

Q31. For turbulent flow in pipes, the velocity distribution follows:

Q32. In fluid statics, the pressure intensity increases with:

Q33. The term used for flow in which velocity at a point changes with time is:

Q34. A device used to measure high fluid velocities is:

Q35. If Mach number is less than 1, the flow is called:

Q36. The ratio of specific weight to specific volume is equal to:

Q37. In a venturimeter, the pressure is minimum at:

Q38. Kinematic viscosity is the ratio of:

Q39. Bernoulli’s theorem assumes:

Q40. Which one is not a dimensionless number?

Q41. Capillary rise is more in:

Q42. A floating body is in stable equilibrium when its:

Q43. The unit of dynamic viscosity in SI system is:

Q44. The instrument used to measure absolute pressure is:

Q45. The pressure intensity at the base of a fluid column is independent of:

Q46. The unit of kinematic viscosity in SI system is:

Q47. Continuity equation represents conservation of:

Q48. Pressure in a moving liquid is measured by:

Q49. For a floating body to be stable:

Q50. Reynold's number is the ratio of:

Q51. Open channel flow is characterized by:

Q52. The pressure at a point in a static fluid:

Q53. The SI unit of pressure is:

Q54. Which instrument measures very small pressure differences?

Q55. Cavitation occurs in a pump when:

Q56. The main cause of major head loss in pipe flow is:

Q57. Hydraulic gradient line (HGL) represents:

Q58. A stream line and equipotential line in a flow field are:

Q59. The slope of the energy grade line (EGL) in pipe flow represents:

Q60. In open channel, critical flow occurs when:

Q61. The discharge in a venturimeter increases if:

Q62. A negative pressure head in a piezometer indicates:

Q63. Manometric head is the:

Q64. Unit of specific speed of a turbine in SI is:

Q65. Flow rate through a pipe increases if:

Q66. The velocity distribution in laminar flow through a circular pipe is:

Q67. The Mach number is defined as:

Q68. Pressure drop in laminar flow is proportional to:

Q69. Hydraulic jump is commonly observed in:

Q70. Which principle is used in venturimeter?

Q71. The dimension of dynamic viscosity is:

Q72. The flow is said to be steady when:

Q73. The maximum efficiency of a centrifugal pump occurs at:

Q74. Surface tension is due to:

Q75. Reynolds number determines:

Q76. Bernoulli’s theorem is applicable to:

Q77. The continuity equation is based on the principle of conservation of:

Q78. A Pitot tube is used to measure:

Q79. A venturimeter is preferred over an orifice meter because:

Q80. Absolute pressure is equal to:

Q81. The pressure of fluid measured above absolute zero pressure is known as:

Q82. The point in a submerged body through which buoyant force acts is called:

Q83. Turbulent flow occurs when Reynolds number exceeds:

Q84. Capillarity is inversely proportional to:

Q85. Hydraulic jump is a phenomenon in:

Q86. The unit of kinematic viscosity in SI system is:

Q87. Centre of pressure on a submerged vertical plane surface is:

Q88. In a floating body, stability depends on:

Q89. The total head line in pipe flow is called:

Q90. In venturimeter, minimum pressure occurs at:

Q91. The Froude number is the ratio of:

Q92. Absolute pressure below atmospheric pressure is called:

Q93. Cavitation in a hydraulic machine is caused by:

Q94. The pressure intensity at a point in a static fluid:

Q95. The dimension of surface tension is:

Q96. Which device measures discharge in open channels?

Q97. The discharge equation of a rectangular weir is proportional to:

Q98. Specific gravity is the ratio of:

Q99. Flow through a nozzle attached to a pipe is an example of:

Q100. The pressure measured by a piezometer is:

Q101. The vena contracta is formed:

Q102. Which statement about viscosity is true?

Q103. The hydraulic radius is defined as:

Q104. Capillarity is directly proportional to:

Q105. The discharge of a nozzle is maximum when:

Fluid Mechanics

📖 Fluid Statics & Pressure Measurement

Hydrostatic Pressure Force on a Submerged Surface

$$ F = \rho \cdot g \cdot \bar{h} \cdot A $$

Where:
\( \rho \) = Density of fluid (kg/m³)
\( g \) = Acceleration due to gravity (9.81 m/s²)
\( \bar{h} \) = Depth of centroid of the submerged area below free surface (m)
\( A \) = Wetted area of the surface (m²)

Center of Pressure (\( h^* \))

$$ h^* = \bar{h} + \frac{I_G \sin^2(\theta)}{A \cdot \bar{h}} $$

Where:
\( I_G \) = Moment of inertia of the area about the centroidal axis (m⁴)
\( \theta \) = Angle of inclination of the surface with the horizontal liquid surface

📖 Fluid Kinematics & Continuity Equation

General Continuity Equation (3D Incompressible Flow)

$$ \frac{\partial u}{\partial x} + \frac{\partial v}{\partial y} + \frac{\partial w}{\partial z} = 0 $$

Where:
\( u, v, w \) = Velocity components in \( x, y, z \) directions (m/s)

1D Continuity Equation (Steady Incompressible Flow)

$$ A_1 V_1 = A_2 V_2 $$

Where:
\( A_1, A_2 \) = Cross-sectional areas at sections 1 and 2 (m²)
\( V_1, V_2 \) = Mean flow velocities at sections 1 and 2 (m/s)

📖 Dynamics of Fluid Flow & Bernoulli’s Equation

Bernoulli’s Equation (Real Fluids with Head Loss)

$$ \frac{p_1}{\gamma} + \frac{V_1^2}{2g} + z_1 = \frac{p_2}{\gamma} + \frac{V_2^2}{2g} + z_2 + h_L $$

Where:
\( \frac{p}{\gamma} \) = Pressure head (m)
\( \frac{V^2}{2g} \) = Kinetic energy / velocity head (m)
\( z \) = Potential / elevation head (m)
\( h_L \) = Total head loss between sections (m)

📖 Laminar & Turbulent Pipe Flow

Reynolds Number (\( Re \))

$$ Re = \frac{\rho V D}{\mu} = \frac{V D}{\nu} $$

Where:
\( V \) = Mean flow velocity (m/s), \( D \) = Diameter of pipe (m)
\( \mu \) = Dynamic viscosity (Pa·s), \( \nu \) = Kinematic viscosity (m²/s)

Darcy-Weisbach Equation for Pipe Friction Head Loss

$$ h_f = \frac{f \cdot L \cdot V^2}{2 \cdot g \cdot D} $$

Where:
\( f \) = Darcy friction factor (\( f = \frac{64}{Re} \) for laminar flow)
\( L \) = Length of pipe (m)

📖 Flow Measurement (Notches & Weirs)

Discharge over a Rectangular Weir / Notch

$$ Q = \frac{2}{3} C_d \cdot L \cdot \sqrt{2g} \cdot H^{3/2} $$

Where:
\( C_d \) = Coefficient of discharge
\( L \) = Length of the crest of the weir (m)
\( H \) = Head of water over the crest (m)

Discharge over a Triangular (V-Notch) Weir

$$ Q = \frac{8}{15} C_d \cdot \tan\left(\frac{\theta}{2}\right) \cdot \sqrt{2g} \cdot H^{5/2} $$

Where:
\( \theta \) = Apex angle of the V-notch

📖 Fluid Properties

Dynamic viscosity \(\mu\) – SI unit Pa·s (N·s/m²). Viscosity of liquids decreases with temperature; of gases increases with temperature.

Ideal fluid – zero viscosity and incompressible (hypothetical).

Specific gravity – ratio of density of fluid to density of water at a standard temperature.

Bulk modulus \(K = -\frac{dp}{dV/V}\); mercury has a high bulk modulus (low compressibility) among common fluids.

Surface tension \(\sigma\) – dimension MT⁻² (or ML⁰T⁻²); enables a liquid surface to resist tensile stress. Capillary rise ∝ surface tension and ∝ 1/diameter.

Pascal’s law – pressure at a point in a static fluid is equal in all directions.

Dimension of pressure: ML⁻¹T⁻².

📖 Dimensionless Numbers
NumberRatio of forcesTypical use
Reynolds \(Re = \rho VD/\mu\)Inertia / ViscousLaminar vs turbulent
Froude \(Fr = V/\sqrt{gL}\)Inertia / GravityFree-surface flows
Mach \(M = V/c\)Inertia / Elastic (speed of sound)Compressible flow
WeberInertia / Surface tensionDroplets, capillary

Pipe flow: laminar if \(Re \lesssim 2000\); turbulent if \(Re \gtrsim 4000\). Critical velocity is the velocity at transition.

📖 Pressure Measurement Devices
  • Barometer – atmospheric pressure.
  • Piezometer – static pressure (simple open tube).
  • U-tube / differential manometer – pressure difference.
  • Inclined manometer – small pressure differences (greater sensitivity).

Vacuum pressure = pressure below atmospheric. Absolute pressure = atmospheric + gauge (or atmospheric − vacuum).

📖 Flow Measurement
  • Venturimeter – discharge in pipes from pressure difference; minimum pressure at the throat.
  • Orifice meter / orifice – vena contracta forms just downstream of the orifice.
  • Pitot tube – local velocity from stagnation pressure.
  • Notches & weirs – discharge in open channels; rectangular weir \(Q \propto H^{3/2}\).
📖 Energy & Hydraulic Grade Lines

Energy grade line (EGL) – total head \(p/\gamma + V^2/(2g) + z\).

Hydraulic grade line (HGL) – piezometric head \(p/\gamma + z\).

Bernoulli’s equation is a statement of mechanical energy conservation along a streamline (for ideal flow) or with head-loss term for real fluids.

Continuity equation is based on conservation of mass.

Streamline – curve that is everywhere tangent to the local velocity vector.

📖 Cavitation & Hydraulic Radius

Cavitation occurs when local pressure falls below the vapour pressure of the liquid (e.g. at pump suction or venturi throat under high velocity).

Hydraulic radius \(R = A/P\) (flow area / wetted perimeter). For a full circular pipe, \(R = D/4\).

Yogendra Gopal Borse

Yogendra Gopal Borse

Civil Engineer | Assistant Engineer Grade-I, Maharashtra PWD

B.Tech (Civil) from VJTI Mumbai. Experienced in bridge design, road works, estimation, project monitoring and digital engineering tools. Creator of YogiPWD – practical technical resources for civil engineers.

Read full About →