MCQ Soil Mechanics

MCQ Soil mechanics

Q1. The unit of permeability coefficient in SI system is:

Q2. Which soil type has the highest permeability?

Q3. The consistency limits of a soil are determined using:

Q4. The unconfined compressive strength test is applicable for:

Q5. Degree of saturation is expressed as:

Q6. The dry density is maximum when:

Q7. The water content at which soil changes from liquid to plastic state is:

Q8. Relative density is applicable to:

Q9. The term 'bulking' is associated with:

Q10. The compressibility of clay is:

Q11. Which method is commonly used for field compaction control?

Q12. CBR test is performed to assess:

Q13. Coefficient of permeability depends mainly on:

Q14. Swelling pressure is significant in:

Q15. Which equipment is preferred for compacting cohesive soils?

Q16. In a soil sample, the void ratio is:

Q17. Which soil has the highest dry density for the same compactive effort?

Q18. The plasticity index is defined as:

Q19. Which soil classification system is used by Indian railways?

Q20. Clay soil particles are predominantly shaped:

Q21. The ratio of weight of water to weight of solids in a soil mass is:

Q22. The ratio of volume of voids to total volume is called:

Q23. Which soil has negligible plasticity?

Q24. Liquid limit can be determined by:

Q25. Effective stress is:

Q26. Consolidation of clay occurs due to:

Q27. The primary cause of settlement in saturated clays is:

Q28. The total unit weight of a fully saturated soil is called:

Q29. Which factor affects the shear strength of soil?

Q30. The critical hydraulic gradient in soils is given by:

Q31. Capillarity rise is more in:

Q32. Soil permeability decreases with:

Q33. The active earth pressure is minimum when:

Q34. The shear strength of cohesionless soils is due to:

Q35. Ultimate bearing capacity is:

Q36. Which one of the following has highest permeability?

Q37. Which test is used to determine unconfined compressive strength?

Q38. The property of soil to resist shear stress is called:

Q39. The air content of a soil sample is:

Q40. Coefficient of curvature (Cc) is given by:

Q41. The compaction of granular soils is best achieved by:

Q42. The consistency index is given by:

Q43. In a grain size distribution curve, a well-graded soil has:

Q44. In Terzaghi’s theory, the time factor (T) is given by:

Q45. Darcy’s law is valid for:

Q46. Critical hydraulic gradient leads to:

Q47. The principal stress in vertical direction in saturated soil is:

Q48. A soil is said to be over-consolidated if:

Q49. The clay mineral having highest swelling potential is:

Q50. The ratio of saturated unit weight to dry unit weight is always:

Q51. The laboratory test generally used for determining permeability of clayey soil is:

Q52. Coefficient of consolidation is affected by:

Q53. The value of compression index (Cc) for a normally consolidated clay can be estimated from:

Q54. The area under the e-log p curve in a consolidation test represents:

Q55. The maximum dry density of a soil is achieved at:

Q56. The ratio of volume of air voids to total volume of voids is known as:

Q57. The unconfined compressive strength test is conducted on:

Q58. Which soil shows dilatancy behavior when sheared?

Q59. Which method is commonly used for determining shear strength of soil in lab?

Q60. Coefficient of volume compressibility (mv) is:

Q61. The shear strength parameters of a soil are determined from:

Q62. A soil with Cu > 4 and 1 < Cc < 3 is considered:

Q63. Bulking of sand occurs due to:

Q64. The major factor influencing permeability of soil is:

Q65. If the degree of saturation is 100%, then air content is:

Q66. Quick condition in soil occurs when:

Q67. Critical hydraulic gradient depends upon:

Q68. During consolidation, rate of settlement is directly proportional to:

Q69. The plastic limit of a soil is:

Q70. The Atterberg limits are applicable to:

Q71. The main reason for soil compaction in the field is to:

Q72. The triaxial test is preferred over the direct shear test because:

Q73. The standard proctor test uses a hammer of:

Q74. The primary consolidation of soil occurs due to:

Q75. Which one of the following clays exhibits highest plasticity?

Q76. Coarse-grained soils are classified by:

Q77. Degree of saturation is zero when:

Q78. Which of the following increases permeability of soil?

Q79. Shear strength of a soil is mainly contributed by:

Q80. Plasticity index is defined as:

Q81. The consistency of a fine-grained soil is expressed by:

Q82. In a flow net, the flow lines and equipotential lines:

Q83. Which one of the following affects the compaction characteristics of soil?

Q84. Specific gravity of soil solids is typically determined using:

Q85. The shear strength of saturated clay under undrained conditions is equal to:

Q86. A high liquid limit indicates:

Q87. Standard penetration test (SPT) is used to determine:

Q88. Which factor influences the effective stress in soil?

Q89. Compaction energy is directly proportional to:

Q90. Piping in soil occurs when:

Q91. The unit of coefficient of permeability is:

Q92. Which test is suitable for determining field density of cohesive soils?

Q93. The term ‘cohesionless soil’ refers to:

Q94. Which IS code provides guidelines for soil classification?

Q95. The maximum dry density obtained by modified proctor test is:

Q96. Which soil property increases permeability?

Q97. Consistency index (Ic) is defined as:

Q98. During compaction, optimum moisture content (OMC) is:

Q99. The bearing capacity of soil mainly depends on:

Q100. Which soil has the maximum void ratio?

Soil Mechanics & Geotechnical Engineering

📖 Phase Relationships & Index Properties

Basic Volume & Weight Relationships

$$ e = \frac{V_v}{V_s}, \quad n = \frac{V_v}{V} = \frac{e}{1 + e} $$

$$ S_r \cdot e = w \cdot G $$

$$ \gamma_d = \frac{G \gamma_w}{1 + e} = \frac{\gamma}{1 + w} $$

Where:
\( e \) = Void ratio, \( n \) = Porosity
\( V_v \) = Volume of voids, \( V_s \) = Volume of solids, \( V \) = Total volume
\( S_r \) = Degree of saturation, \( w \) = Water content
\( G \) = Specific gravity of soil solids, \( \gamma_d \) = Dry unit weight, \( \gamma \) = Bulk unit weight

📖 Effective Stress Principle

Effective Stress (\( \sigma' \))

$$ \sigma' = \sigma - u $$

Where:
\( \sigma \) = Total stress at a given point (kN/m²)
\( u \) = Pore water pressure \( = h_w \gamma_w \) (kN/m²)
\( \sigma' \) = Effective intergranular stress (kN/m²)

📖 Permeability & Seepage

Darcy’s Law of Flow

$$ v = k \cdot i, \quad Q = k \cdot i \cdot A $$

Where:
\( v \) = Discharge velocity (m/s), \( k \) = Coefficient of permeability (m/s)
\( i \) = Hydraulic gradient \( = \frac{\Delta h}{L} \), \( A \) = Total cross-sectional area

Seepage Velocity (\( v_s \))

$$ v_s = \frac{v}{n} = \frac{k \cdot i}{n} $$

📖 Consolidation Settlement

Primary Consolidation Settlement (\( S_c \))

$$ S_c = \frac{H_0}{1 + e_0} C_c \log_{10} \left( \frac{\sigma'_0 + \Delta\sigma'}{\sigma'_0} \right) $$

Where:
\( H_0 \) = Initial thickness of compressible layer (m)
\( e_0 \) = Initial void ratio
\( C_c \) = Compression index
\( \sigma'_0 \) = Initial effective overburden pressure (kN/m²)
\( \Delta\sigma' \) = Increment in effective stress due to loading (kN/m²)

Time Factor and Degree of Consolidation

$$ T_v = \frac{c_v \cdot t}{d^2} $$

Where:
\( T_v \) = Time factor (depends on percentage consolidation \( U\% \))
\( c_v \) = Coefficient of consolidation (m²/s)
\( t \) = Time (s)
\( d \) = Drainage path length (half-thickness for double drainage, full thickness for single drainage)

📖 Shear Strength & Bearing Capacity

Mohr-Coulomb Failure Criterion

$$ \tau_f = c' + \sigma' \tan(\phi') $$

Where:
\( \tau_f \) = Shear strength at failure (kN/m²)
\( c' \) = Effective cohesion intercept (kN/m²)
\( \phi' \) = Effective angle of internal friction

Terzaghi’s Ultimate Bearing Capacity Formula (Strip Footing)

$$ q_u = c N_c + q N_q + 0.5 \gamma B N_\gamma $$

Where:
\( q_u \) = Ultimate bearing capacity (kN/m²)
\( c \) = Cohesion of soil, \( q = \gamma D_f \) = Surcharge at foundation base level
\( B \) = Width of footing, \( \gamma \) = Unit weight of soil
\( N_c, N_q, N_\gamma \) = Terzaghi’s bearing capacity factors

📖 Atterberg Limits & Consistency Indices

Liquid Limit (LL) – water content at which soil passes from plastic to liquid state (Casagrande apparatus / cone penetrometer).

Plastic Limit (PL) – water content at which soil changes from semi-solid to plastic state (thread of 3 mm diameter starts to crumble).

Shrinkage Limit (SL) – water content below which further loss of moisture does not cause decrease in volume.

$$ I_P = LL - PL \quad \text{(Plasticity Index)} $$

$$ I_C = \frac{LL - w}{LL - PL} \quad \text{(Consistency Index)} $$

$$ I_L = \frac{w - PL}{LL - PL} \quad \text{(Liquidity Index)} $$

High LL generally indicates high compressibility. Clay particles are typically plate-like.

📖 Compaction

Optimum Moisture Content (OMC) – water content at which maximum dry density (MDD) is obtained for a given compactive effort.

$$ \gamma_d = \frac{\gamma}{1 + w} $$

Standard Proctor vs Modified Proctor: modified test uses higher energy → higher MDD and lower OMC.

Compaction energy ∝ number of blows × hammer weight × drop height.

  • Sheep-foot roller – preferred for cohesive soils.
  • Vibratory / smooth-wheel roller – preferred for cohesionless soils.
  • Field density – sand-replacement method (general); core-cutter method (cohesive soils).

Relative density is used for cohesionless soils:

$$ D_r = \frac{e_{\max} - e}{e_{\max} - e_{\min}} \times 100\% $$

📖 Permeability Notes

Coefficient of permeability \(k\) has units m/s. It depends mainly on particle size (and void ratio, fabric). Sand has high permeability; clay has very low permeability. Higher porosity generally increases permeability.

Piping occurs when seepage force exceeds the effective weight of soil particles (critical hydraulic gradient ≈ 1 for many soils).

📖 Strength & Related Tests
  • UCS (Unconfined Compression Strength) – applicable to saturated cohesive soils; \(q_u = 2c_u\) for \(\phi_u = 0\).
  • Undrained shear strength of saturated clay ≈ cohesion only (\(\phi_u = 0\)).
  • CBR – assesses subgrade strength for pavement design.
  • SPT – used to estimate relative density / consistency and approximate shear strength parameters.
  • Bearing capacity of foundations depends primarily on shear strength of soil (Terzaghi formula already given above).
📖 Classification & Miscellaneous
  • IS classification of soils: IS 1498.
  • Indian Railways traditionally used HRB / AASHTO-type systems; modern practice also refers to IS 1498.
  • Bulking of sand – apparent increase in volume of moist sand due to films of water around particles.
  • Specific gravity of soil solids is determined by pycnometer (or density bottle).
  • Expansive clays develop significant swelling pressure upon wetting.
  • Clays typically have the highest void ratios among common mineral soils.
Yogendra Gopal Borse

Yogendra Gopal Borse

Civil Engineer | Assistant Engineer Grade-I, Maharashtra PWD

B.Tech (Civil) from VJTI Mumbai. Experienced in bridge design, road works, estimation, project monitoring and digital engineering tools. Creator of YogiPWD – practical technical resources for civil engineers.

Read full About →