MCQ Transportation Engineering

MCQ MCQ Transportation

Q1. The ruling gradient is provided in road design to:

Q2. Camber in roads is primarily provided for:

Q3. IRC stands for:

Q4. The super-elevation on a curve is provided to:

Q5. The width of a single lane carriageway as per IRC is:

Q6. The stopping sight distance depends on:

Q7. The term ‘At-grade intersection’ means:

Q8. Bitumen is preferred for road works because it is:

Q9. Marshall Stability test is conducted to determine:

Q10. Design speed for National Highways as per IRC is typically:

Q11. The purpose of providing shoulders on a road is to:

Q12. Flexible pavements distribute wheel loads:

Q13. Which of the following is not a traffic control device?

Q14. The maximum super-elevation recommended by IRC in plain terrain is:

Q15. Traffic volume is measured in:

Q16. CBR stands for:

Q17. The most important property for aggregates in bituminous construction is:

Q18. An example of an intersection control device is:

Q19. Which layer in flexible pavement acts as a wearing surface?

Q20. Transition curves are provided in horizontal alignment to:

Q21. The main function of a road subgrade is to:

Q22. The desirable camber for bituminous roads in India typically ranges from:

Q23. The formula to calculate super-elevation is:

Q24. Design of rigid pavements is based on:

Q25. Which road type is highest in road classification hierarchy?

Q26. Which of the following primarily determines overtaking sight distance?

Q27. In the wheel load distribution of flexible pavements, stress decreases:

Q28. Which IS code covers CBR testing for subgrade soils?

Q29. The flexible pavement layer directly resting on subgrade is:

Q30. In rigid pavements, warping stresses are caused by:

Q31. The maximum allowable gradient in hilly terrain as per IRC is:

Q32. The design life of National Highway flexible pavements as per IRC:37 is:

Q33. The aggregate impact value (AIV) for road aggregates should preferably be less than:

Q34. The IRC code for the design of flexible pavements is:

Q35. WBM stands for:

Q36. The ideal shape of aggregates for road construction is:

Q37. Overtaking zones on highways are provided:

Q38. The modulus of subgrade reaction is denoted by:

Q39. The main factor for determining traffic volume is:

Q40. The permissible axle load for single axle vehicles as per IRC is:

Q41. The highest design speed is provided for which type of road as per IRC?

Q42. Roadway width for a two-lane undivided road in plain terrain as per IRC is:

Q43. Which traffic study determines speed trends on roads?

Q44. The purpose of providing a median on highways is:

Q45. The main advantage of traffic rotaries is:

Q46. The most suitable shape of transition curve in road design is:

Q47. Axle load survey is primarily conducted to:

Q48. Maximum axle load for a tandem axle as per IRC guidelines is:

Q49. Road user cost includes:

Q50. Pavement performance is assessed based on:

Q51. Traffic volume studies are usually conducted over a period of:

Q52. The term PCU in traffic studies stands for:

Q53. Stopping sight distance (SSD) depends on:

Q54. The unit of road roughness index (RRI) is:

Q55. Which of these is a bituminous surface dressing?

Q56. The term 'ruling gradient' is used in:

Q57. Which layer in flexible pavement distributes load to subgrade?

Q58. Which method is widely used for flexible pavement design in India?

Q59. Skid resistance of road surface is affected by:

Q60. IRC recommends what camber for cement concrete roads in heavy rainfall areas?

Q61. The value of camber provided on bituminous roads in heavy rainfall areas as per IRC is:

Q62. The desirable carriageway width for a two-lane undivided road without kerbs is:

Q63. The ruling gradient recommended for plain terrain as per IRC is:

Q64. Super-elevation on horizontal curves is provided to:

Q65. The ideal shape of valley curves is:

Q66. For parking studies, the most suitable survey method is:

Q67. The highest PCU value is assigned to:

Q68. The term “design period” in pavement design implies:

Q69. Warping stresses are considered in:

Q70. The major factor for design of shoulders is:

Q71. The object of providing camber on roads is to:

Q72. In rigid pavement design, temperature stresses are caused due to:

Q73. The maximum super-elevation permitted for hilly roads in snowbound areas is:

Q74. Which of the following is a traffic regulatory sign?

Q75. The total reaction time of a driver recommended by IRC is:

Q76. The main cause of rutting in flexible pavements is:

Q77. Which of the following traffic studies is conducted for measuring vehicle speeds at a specific location?

Q78. The term “pavement deflection” refers to:

Q79. Benkelman Beam is used for:

Q80. The design life of rigid pavements as per IRC:58-2015 is:

Q81. The width of a single-lane carriageway recommended by IRC is:

Q82. The traffic flow condition where vehicles can move freely without hindrance is called:

Q83. The standard axle load used for pavement design as per IRC is:

Q84. In traffic engineering, the term ‘PCU’ is expressed as a ratio of:

Q85. The main reason for providing shoulders on highways is to:

Q86. The minimum value of super-elevation provided on highways is:

Q87. The main cause of bleeding in bituminous roads is:

Q88. IRC recommends a maximum gradient of ____ for plain terrain.

Q89. Which of the following is a flexible pavement distress?

Q90. The capacity of a rotary is expressed as:

Q91. In traffic engineering, the term 'capacity' refers to:

Q92. The maximum permissible camber for a bituminous road surface in heavy rainfall areas is:

Q93. The stopping sight distance (SSD) increases with:

Q94. The most appropriate curve for highways in hilly areas is:

Q95. The design speed for National Highways in plain terrain as per IRC is:

Q96. The primary purpose of a 'transition curve' is to:

Q97. The rolling resistance on a highway is minimum for:

Q98. Bituminous roads are more preferred in India because:

Q99. Which one of the following is a surface distress observed in flexible pavements?

Q100. The test conducted to determine the toughness of aggregates is:

Transportation Engineering

Stopping sight distance

 Stopping sight distance (SSD in 'metres') of a vehicle is the sum of :

1) The distance travelled by the vehicle during the total reaction time known as lag distance and 

$${\text{Lag distance}}=0.278Vt$$

2) The distance travelled by the vehicle after the application of the brakes, to a dead stop position which is known as braking distance.

$${\text{Braking distance}}={{V^2}\over {254(f\pm S \%)}}$$

$$\text{SSD = Lag distance + Braking distance}$$

$$SSD = 0.278Vt + {{V^2}\over {254(f\pm S \%)}}$$

Where S% is gradient '+' sign for ascending gradient & '-' sign for descending gradient

Overtaking Sight Distance (OSD)

The minimum distance open to the vision of a driver of a vehicle intending to overtake slow vehicle ahead with safety against the traffic of opposite direction is known as minimum overtaking sight distance (OSD) or safe passing sight distance available.

OSD = d1+ d2+ d3  ...... Where OSD is overtaking site distance in 'm'
$${d_1}={0.278 V_b t}$$

$${d_2}=b+2S$$

OR

$${d_2}={0.278 V_b t}+{{a T^2}\over 2}$$

Where, S = minimum spacing between 2 vehicles

$$S = 0.2{V_b}+6$$ 
here Vb is in km/hr.

$$T = {\sqrt{4s\over a}}$$
Where, a = acceleration in 'm/s2'

$$T = {\sqrt{14.4s\over a}}$$
Where, a = acceleration in 'km/hr/sec'

$${d_3}={0.278 V_c T}$$

Where, d3  = distance travelled by on coming vehicle from C1 to C2  during overtaking operation
Vc = V= Speed of overtaking vehicle or design speed (km/hr)
if Vb is not given then
Vb = (V-16) ..................in km/hr
Vb = (V-4.5) ..................in m/s

For 1 way traffic 
OSD = d1+ d2
For 2 way traffic 
OSD = d1+ d2+ d3
Minimum length of overtaking zone = 3 x OSD

Desirable overtaking zone = 5 x OSD

Important equation and terminology checks

  • Traverse balancing: corrections must oppose the closing errors. The Compass/Bowditch and Transit correction equations above are written with a minus sign for this reason.
  • Direction of closing error: use \(\operatorname{atan2}(\sum D,\sum L)\), or determine the quadrant from the signs of the total latitude and departure. A simple \(\tan^{-1}(\sum D/\sum L)\) alone can give the wrong quadrant.
  • Area by cross-staff/offsets: for a series of offsets at equal spacing, use the trapezoidal summation \(A=\frac{d}{2}\sum_{i=1}^{n-1}(O_i+O_{i+1})\). A single \(\frac12(L_1+L_2)d\) applies to one interval only.
  • Curvature and refraction: the constants shown in the notes assume distance \(d\) in kilometres and correction in metres. Curvature correction is normally subtracted from observed staff readings; combined curvature-refraction correction is approximately \(0.0673d^2\) m under standard assumptions.
  • Stopping sight distance: \(SSD=0.278Vt+\frac{V^2}{254(f\pm G)}\) is a commonly used metric form when \(V\) is in km/h, \(t\) in seconds, \(f\) is the longitudinal friction factor, and \(G\) is gradient as a decimal. If the gradient is entered as a percentage number, the denominator convention must be adjusted; do not insert “S%” without clarifying whether it means percent or decimal.
  • Overtaking sight distance: the source contains alternative expressions and assumptions for \(d_2\), \(T\), and vehicle speeds. These depend on the design standard and unit convention; verify against the applicable IRC standard before using them for design.
  • Scope: these are formatted study notes, not a substitute for checking the applicable surveying/IRC standard or project specifications.
Terrain Catogory Over taking Sight Distance Safe stopping sight for minimum design speed Safe stopping sight for Rulling design speed
Plain Terrain 475 120 170
Rolling Terrain 310 90 120
Hilly Terrain - 50 60
Steep - 40 50

Super Elevation (e)

The Super Elevation 'e' is expressed as the ratio of the height of outer edge with respect to horizontal width.

$$e={NL\over ML} = tan\theta = {{V^2}\over 225R}$$

$$e+f = {{V^2}\over 127R}$$

Where, 
V= speed in km/hr
R = Radius in 'm'
f = design value of lateral friction = 0.15
e = rate of super elevation

Maximum Super Elevation
emaxTerrain Type
0.07Plain and Rolling Terrain
0.10Hilly Area
0.04
Urban roads with frequent intersections


Ruling minimum radius of the curve


$${R_{Ruling}} = {{V^2}\over {127(e+f)}}$$

Radii for horizontal curves in meters

Terrain Catogory Absolute Rulling
Plain Terrain 250 370
Rolling Terrain 155 250
Hilly Terrain 50 80
Steep 3050

Extra Widening (Ew)

Extra widening of pavement on horizontal curves is divided into 2 parts
1) Mechanical Widening (Wm):- The widening required to account for the off-tracking due to the rigidity of wheel base is called mechanical widening.
$$W_m = {{n{l^2}}\over 2R}$$

2) Psychological Widening (Wp):- Extra width of pavement is also provided for psychological reason such as to provide for greater maneuverability of steering at higher speeds, to allow for extra space requirements for the overhangs of the vehicles and to provide greater clearance for crossing and overtaking vehicles on the curves. Psychological widening is important in pavements with more than 1 lane.
$$W_p = {V\over {9.5\sqrt{R}}}$$

Combined Extra widening required on curves

$$E_w = W_m + W_p $$

$$E_w = {{n{l^2}}\over 2R} +{V\over {9.5\sqrt{R}}}$$

Transition Curve

The Indian road congress (IRC) reccomends the use of spiral as transition curve in the horizontal alignment of highways due to following reasons:
(i) The Spiral Curve satisfies the requirements of ideal transition.
(ii) The geometric properties of spiral is such that the calculations and setting out the curve in the field is simple and easy.

Length of transition curve (L)

(i) According to rate of change of centrifugal acceleration


$$L = {{0.0215 V^3}\over CR}$$

Where, V = Speed of vehicle in (km/hr)
                C = Allovable rate of change of centrifugal acceleration in (m/s2)
                R = Radius of curve in (m)
                L = Length of transition curve in (m)

(ii) According to rate of change of super elevation

$$L = {\text {150x → For Plain & Rolling Terrain}}$$

$$L = {\text {100x → For Built up area}}$$

$$L = {\text {60x → For Hilly area}}$$

Whre, x = Raise of outer line of road

$$x = (w + E_w )e \text{....... if the pavement rotated about inner side}$$

$$x = (w + E_w ){e \over 2} \text{....... if the pavement rotated about centre line}$$

(iii) According to empirical formula

$$L = {{2.7 V^2}\over R}\text{...........For Plain and Rolling terrain}$$

Note:- This is as per IRC and its minimum value of Transition curve.

$$L = {{V^2}\over R}\text{...........For Hilly area}$$




To find out offset length at desired chainage 'x' the equation of cubical parabola

$$Y = {{x^3}\over {6RL}}$$

$${Shift}= {{{L_s}^2}\over {24R}}$$

$${L_s}={{E\times N}\over 2}$$

$${E\over 2} = {\text {Total Raise of outer edge of Pavement}} ={{eB}\over 2}$$

$$N ⟶{\text {Rate of Distribution of super elevation}}$$

Set Back Distance (m)

The clearance distance or set back distance required from the centre lines of a horizontal curve to an obstruction on the inner side of the curve to provide adequate sight distance depends upon the following factors :
(i) Required Sight distance (SSD)
(ii) Radius of horizontal curve, (R)
(iii) Length of the curve (Lc)

1. For Single lane road


(a) When Lc > SSD

 $$m = R - R.{Cos{{\alpha} \over 2}}$$

&

$${\alpha \over 2}={{180.s}\over {2\Pi R}}$$

Where, Lc = Length of Curve & s = SSD

(b) Lc < SSD

$$m=R\left({1-cos{\alpha \over 2}}\right) + {{S - L_c}\over 2} sin{\alpha \over 2}$$

&

$${\alpha \over 2}={{180.L_c}\over {2\Pi R}}$$

2. For two lane road


(a) When Lc > SSD

 $$m = R - (R-d){Cos{{\alpha} \over 2}}$$

&

$${\alpha \over 2}={{180.s}\over {2\Pi (R-d)}}$$

Where, Lc = Length of Curve & s = SSD

(b) Lc < SSD

$$m=R-(R-d)\left({1-cos{\alpha \over 2}}\right) + {{S - L_c}\over 2} sin{\alpha \over 2}$$

&

$${\alpha \over 2}={{180.L_c}\over {2\Pi (R-d)}}$$

Grade Compensation

$$\text{Grade Compensation}={{30 + R}\over R}\%$$

And 

$$\text{Maximum value of Grade Compensation}={{75}\over R}\%$$

Where, R = radius of curve in meter

Vertical Curve

Due to changes in grade in vertical alignment of highway, it is necessary to introduce vertical curves at the intersections of different grades to smoothen out the vertical profile and thus ease off changes in gradients for fast moving vehicles.

The vertical curves used in highways may be classified into two categories :

Transportation Engineering – Geometric Design & Pavements

📖 Camber, Gradient & Cross-Section Elements

Camber (cross slope) – primarily provided for surface drainage of rainwater. Typical values (IRC): 1.7–2.5 % for bituminous, 2–3 % for gravel, higher for earth roads.

Ruling gradient – the maximum gradient that can be adopted for a given terrain and design speed without causing excessive strain on vehicles; balances safety, economy and vehicle performance.

Shoulders – provide lateral support to the pavement, space for emergency stopping, and improve capacity and safety.

Carriageway widths (IRC typical):

  • Single lane: 3.75 m
  • Two-lane (without raised kerbs): 7.0 m (often 7.5 m with kerbs)
  • Multi-lane: 3.5 m per lane

Design speed (NH, plain terrain): commonly 80–100 km/h as per IRC.

📖 Super-elevation & Transition Curves

Super-elevation (e) counters centrifugal force on horizontal curves:

$$ e + f = \frac{V^2}{127 R} $$

where \(V\) in km/h, \(R\) in m, \(f\) = lateral friction coefficient.

IRC maximum super-elevation: 1 in 15 (≈ 7 %) in hilly terrain; 1 in 20 (5 %) in plain & rolling terrain (to avoid toppling of slow vehicles / discomfort).

Transition curves (usually clothoid / cubic parabola) are provided so that centrifugal force and super-elevation are introduced gradually; they also improve aesthetics and visibility.

📖 Sight Distance

Stopping Sight Distance (SSD)

$$ SSD = 0.278\,V\,t + \frac{V^2}{254(f \pm 0.01 n)} $$

where \(V\) = speed (km/h), \(t\) = reaction time (usually 2.5 s), \(f\) = longitudinal friction, \(n\) = gradient (%). SSD depends on reaction time, speed, friction and gradient.

Overtaking Sight Distance (OSD) and Intermediate Sight Distance (ISD ≈ 2 × SSD) are used for two-lane two-way roads.

📖 Flexible vs Rigid Pavements
  • Flexible pavement – bituminous surface; load is distributed layer by layer through grain-to-grain contact to the subgrade. Layers: surface course (wearing) → binder → base → sub-base → subgrade.
  • Rigid pavement – cement concrete slab; load is distributed by slab action (beam/plate action) over a wide area of subgrade. Design uses Westergaard analysis.

CBR (California Bearing Ratio) – empirical measure of subgrade strength; used extensively in flexible pavement design (IRC:37).

$$ E_{\text{subgrade}} \approx 17.6\,(\text{CBR})^{0.64}\ \text{MPa}\quad (\text{CBR} > 5\%) $$

📖 Bituminous Materials & Marshall Test

Bitumen is preferred because it is thermoplastic, adhesive and waterproof. Marshall Stability test determines stability (strength) and flow of bituminous mixes and is used for mix design.

Important aggregate properties for bituminous work: toughness (impact), hardness (abrasion), shape (flakiness/elongation), water absorption and affinity to bitumen.

📖 Traffic & Intersections
  • Traffic volume – vehicles per hour or per day (AADT, ADT, peak hour volume).
  • At-grade intersection – roads meet at the same level (as opposed to grade-separated interchanges).
  • Traffic control devices: signs, markings, signals, speed breakers. Camber and super-elevation are geometric elements, not control devices.
📖 Design Traffic (IRC:37)

Vehicle Damage Factor (VDF)

$$ \text{VDF} = \left( \frac{\text{Axle load}}{\text{Standard axle load}} \right)^4 $$

Cumulative standard axles (simplified form)

$$ N = 365 \times A \times D \times F \times \frac{(1+r)^n - 1}{r} $$

(or equivalent forms using growth factor); \(A\) = initial commercial vehicles/day, \(D\) = lane distribution factor, \(F\) = VDF, \(r\) = growth rate, \(n\) = design life.

(i) Summit curves or crest curves with convexity upwards
(ii) Valley or sag curves with concavity upwards.

Summit curves (Crest curve with convexity upwards):

Summit curves with convexity upwards are formed in any one of the case illustrated in fig. The deviation angles between the two interacting gradients is equal to the algebraic difference between them. Of all the cases, the deviation angles will be maximum when an ascending gradient meets with a descending gradient. i.e. N = n1 - (- n2) = n1 + n2

(i) Length of Summit curve for SSD

(a) When L > SSD

$$L = {{NS^2}\over {(\sqrt{2H} + \sqrt{2h})^2}}$$


$$L = {{NS^2}\over 4.4}$$

Where, L = Length of summit curve in meter
            S = SSD (m)
            N = Deviation Angle
                = Algebraic deference of grade
            H = Height of eye level of driver above road way surface ≈ 1.2 m
            H = Height of object above Pavement surface ≈ 0.15 m

(a) When L < SSD


$$L = 2S-{{(\sqrt{2H} + \sqrt{2h})^2}\over N}$$

$$L = 2S - {4.4\over N}$$

(ii) Length of Summit curve for Safe Overtaking Distance (OSD) or Intermediate Sight Distance (ISD)

(a) When L > OSD

$$L = {{N{S_o}^2}\over {(\sqrt{2H} + \sqrt{2h})^2}}$$


$$L = {{N{S_o}^2}\over 9.6}$$

Where, So = Overtaking or Intermediate sight distance

(b) When L < OSD

$$L = 2S-{{(\sqrt{2H} + \sqrt{2h})^2}\over N}$$

$$L = 2{S_o} - {9.6\over N}$$

Valley Curves (Sag curve with Concavity Upward):


(i) Length of Valley curve as per comfort condition (Transition curves are provided back to back)
$$L=2\left[NV^3 \over C\right]^{1\over 2}$$

if C = 0.6 m/s2 then 

$$L=0.38(NV^3)^{1\over 2}$$

(ii) Length of Valley curve for head light sight distance (Parabolic Curve is provided)

Summit curves (Crest curve with convexity upwards):

Summit curves with convexity upwards are formed in any one of the case illustrated in fig. The deviation angles between the two interacting gradients is equal to the algebraic difference between them. Of all the cases, the deviation angles will be maximum when an ascending gradient meets with a descending gradient. i.e. N = n1 - (- n2) = n1 + n2

(i) Length of Summit curve for SSD

(a) When L > SSD

$$L = {{NS^2}\over {(2h_1 + 2S.tan\alpha)}}$$


$$L = {{NS^2}\over {1.5+0.035S}}$$

Where, L = Total Length of Valley curve in meter
            S = SSD (m)
            N = Deviation Angle
                = Algebraic deference of grade
            α = Beam Angle ≈ 1o
            h1 = Avg. Height of headlight above Pavement surface ≈ 0.75 m

(a) When L < SSD


$$L = 2S-{{(2h_1 + 2S.tan\alpha)}\over N}$$

$$L = 2S - {{1.5+0.035S}\over N}$$

Vehicle Damage Factor (VDF)  
$$ \text{VDF} = \left( \frac{\text{Axle Load (kN)}}{\text{Standard Axle Load (kN)}} \right)^4 $$  

Cumulative Number of Standard Axles (N)  
$$ N = 365 \times A \times D \times F \times \left( 1 + r \right)^n $$  

where:  
\( A \) = initial commercial vehicles/day  
\( D \) = lane distribution factor  
\( F \) = vehicle damage factor  
\( r \) = growth rate  
\( n \) = design life in years  

California Bearing Ratio (CBR) Modulus  
$$ E_{subgrade} = 17.6 \times (\text{CBR})^{0.64} \text{ MPa} $$  

Flexible Pavement — Structural Number (AASHTO Method)  
$$ SN = a_1 D_1 + a_2 D_2 m_2 + a_3 D_3 m_3 $$  

where:  
\( a \) = layer coefficient  
\( D \) = layer thickness (in inches)  
\( m \) = drainage coefficient  

IRC:37-2018 — Design Traffic (in msa)  
$$ N = \frac{365 \times A \times (1+r)^n - 1}{r} \times F \times D $$  

Deflection-Based Overlay Design (Benkelman Beam Method)  
$$ \text{Overlay Thickness (mm)} = C \times (\text{Measured Deflection} - \text{Permissible Deflection}) $$  

Rigid Pavement — Westergaard's Stress Equation for Edge Load  
$$ \sigma = \frac{3P}{2\pi h^2} \times \left[ \ln \left( \frac{1.6a}{h} \right) + 0.675 \right] $$  

where:  
\( P \) = wheel load  
\( h \) = slab thickness  
\( a \) = radius of contact area  

Radius of Relative Stiffness (l)  
$$ l = \left( \frac{Eh^3}{12(1-\mu^2)k} \right)^{0.25} $$  

where:  
\( E \) = modulus of elasticity  
\( \mu \) = Poisson's ratio  
\( k \) = modulus of subgrade reaction  

Traffic Growth Rate Formula  
$$ T_f = T_0 (1 + r)^n $$  

where:  
\( T_f \) = traffic after \( n \) years  
\( T_0 \) = initial traffic  
\( r \) = growth rate  

Mean Texture Depth (MTD)  
$$ \text{MTD} = \frac{\text{Volume of Sand (ml)}}{\text{Area (mm}^2)} \times 1000 $$


Flexible pavement Design Important formulas  

Resilient modulus is obtained from repeated triaxial test, but it's quite complicated process hence generally it is calculated from CBR value using following co-relations. 4 days soaked CBR is used in such cases.

For CBR ≤ 5%:

$$M_{r,s} = 10 \times CBR$$


For CBR > 5%:

$$M_{r,s} = 17.6 \times CBR^{0.64}$$


Resilient modulus formula from repeated load triaxial test based on recoverable elastic deformation under deviator stress

$$M_{rs} = \frac{2 (1 - \mu^2) \, p_a}{\Delta}$$


Where:

$$ \begin{align*} M_r &= \text{Resilient modulus (MPa)} \\ \mu &= \text{Poisson's ratio of the material (dimensionless)} \\ p_a &= \text{Applied deviator (cyclic) stress (MPa)} \\ \Delta \varepsilon &= \text{Recoverable axial strain (dimensionless)} \end{align*} $$

Fatigue Model (IRC:37-2018)

$$N_f = K_1 \left( \frac{1}{\varepsilon_t} \right)^{K_2} \left( \frac{1}{E_{bit}} \right)^{K_3}$$

Where:

$$ \begin{aligned} N_f &= \text{Number of cumulative standard axles to cause fatigue cracking} \\ \varepsilon_t &= \text{Tensile strain at the bottom of bituminous layer (in microstrain)} \\ E_{bit} &= \text{Elastic modulus of bituminous layer (in MPa)} \\ K_1, K_2, K_3 &= \text{Empirical constants} \end{aligned} $$

As per IRC:37-2018 (Table 4.3):

$$ \begin{aligned} \text{For 90% reliability upto 30msa } K_1 &= 0.516 \times 10^{-4} \\ \text{For 80% reliability upto 30 msa } K_1 &= 1.4064 \times 10^{-4} \\ K_2 &= 3.89 \\ K_3 &= 0.854 \end{aligned} $$

Where (for rutting model):

$$ \begin{aligned} N_d &= \text{Number of cumulative standard axles to cause rutting failure} \\ \varepsilon_v &= \text{Vertical compressive strain on top of subgrade or granular layer} \\ K_4, K_5 &= \text{Empirical constants} \end{aligned} $$

As per IRC:37-2018 (Table 4.4):

$$ \begin{aligned} \text{For 90% reliability upto 30 msa:} \\ K_4 &= 1.41 \times 10^{-8} \\ K_5 &= 4.5337 \\ \text{For 80% reliability upto 30 msa:} \\ K_4 &= 1.84 \times 10^{-8} \\ K_5 &= 4.5337 \end{aligned} $$

Granular Sub Base

graph TD A[Granular Sub base] --> B[Drainage] A[Granular Sub base] --> C[Filter] A[Granular Sub base] --> Z[Drainage + Filter] A[Granular Sub base] --> R[CTSB] B --> D[G3/G4] C --> E[G1/G2] Z --> Y[G5/G6] D --> F[Prevent entering of water to subgrade] D --> L[Minimum thickness is 100 mm] L --> N[2.5 X NMAS] N --> O[Rutting Checking for 10,000 ESAL] E --> L[Minimum thickness is 100 mm] E --> G[Preventing Small particles from Subgrade to top layer] F --> H[On top of Filter Layer] G --> I[In between Drainage and Subgrade] Y --> X[If Design thickness less than 200 mm] H --> J[Used in combination with Filter layer] I --> K[Used in combination with Drainage layer] R --> S[Recommended gradation is G4 with minimum thickness 200 mm] S --> T[E = 1000 X UCS of 28 days] T --> AA[M_r restricted to 600 MPa] AA --> AB[Poisson's ratio = 0.25] X --> W[Minimum thickness is 150 mm]

Resilient modulus for granular layer is function of modulus of subgrade and thickness of granular layer

$$M_{rgran} = 0.2 \times (h)^{0.45} \times M_{rSupport}$$


$$M_{rSupport} \text{ is modulus of support, below layer ubder consideration}$$

Yogendra Gopal Borse

Yogendra Gopal Borse

Civil Engineer | Assistant Engineer Grade-I, Maharashtra PWD

B.Tech (Civil) from VJTI Mumbai. Experienced in bridge design, road works, estimation, project monitoring and digital engineering tools. Creator of YogiPWD – practical technical resources for civil engineers.

Read full About →

Post a Comment

0 Comments