MCQ Reinforced Cement Concrete

MCQ Reinforced Cement Concrete

Q1. The minimum clear cover to main reinforcement in an RCC footing as per IS 456:2000 is:

Q2. In a doubly reinforced rectangular beam, compression steel is provided to:

Q3. In RCC construction, which material primarily resists tensile forces?

Q4. The minimum grade of concrete for RCC as per IS 456:2000 for structural members is:

Q5. The purpose of cover blocks in RCC construction is to:

Q6. In RCC construction, which material primarily resists tensile forces?

Q7. The minimum grade of concrete for RCC as per IS 456:2000 for structural members is:

Q8. The purpose of cover blocks in RCC construction is to:

Q9. What is the usual diameter range for main reinforcement bars in RCC slabs?

Q10. Which of the following is NOT a type of RCC beam?

Q11. What is the typical minimum cover required for RCC footings as per IS 456:2000?

Q12. In RCC, which factor primarily controls shrinkage cracking?

Q13. What is the main purpose of stirrups in RCC beams?

Q14. Which IS code covers general guidelines for plain and reinforced concrete?

Q15. What is the minimum lap length for tension reinforcement in RCC as per IS 456:2000?

Q16. In RCC, the main reinforcement is placed in which zone of a simply supported beam?

Q17. What is the purpose of lateral ties in RCC columns?

Q18. Which of the following is an assumption in the limit state method for RCC design?

Q19. The modular ratio (m) is the ratio of:

Q20. The limit state of serviceability deals with:

Q21. The factor of safety for concrete in limit state of collapse as per IS 456:2000 is:

Q22. For reinforced concrete, the permissible tensile stress in mild steel (Fe 250) is:

Q23. Which type of bar is generally used as stirrups in RCC beams?

Q24. A singly reinforced beam is:

Q25. In RCC, the maximum permissible deflection for simply supported beams under live load is:

Q26. In RCC, the cover for main reinforcement in beams as per IS 456:2000 should not be less than:

Q27. In a cantilever RCC beam, the main tension reinforcement is provided at:

Q28. In RCC, the minimum percentage of longitudinal reinforcement in columns is:

Q29. Creep in concrete is:

Q30. The minimum grade of concrete for RCC as per IS 456:2000 is:

Q31. The diameter of bars used as lateral ties in RCC columns is usually not less than:

Q32. Maximum spacing of stirrups in RCC beams should not exceed:

Q33. Which test determines the workability of fresh concrete?

Q34. The tensile strength of concrete is generally taken as:

Q35. The minimum diameter for main reinforcement bars in RCC slabs should be:

Q36. The water-cement ratio is critical in concrete because it affects:

Q37. The development length of bars in RCC is calculated to:

Q38. Shear reinforcement is provided in RCC beams to:

Q39. Which of the following improves the workability of concrete?

Q40. Which of these bars has higher ductility?

Q41. The function of cover blocks in RCC is to:

Q42. The modulus of elasticity for concrete is primarily influenced by:

Q43. Concrete strength gain continues up to:

Q44. The minimum clear spacing between two parallel reinforcement bars should not be less than:

Q45. Which test is commonly used to determine the compressive strength of concrete?

Q46. What is the minimum number of longitudinal bars in a rectangular RCC column as per IS 456:2000?

Q47. What is the characteristic compressive strength of M25 concrete?

Q48. Which IS code governs the general guidelines for RCC structures?

Q49. Which factor improves the tensile strength of concrete?

Q50. The minimum clear cover for footing reinforcement is:

Q51. In RCC columns, the lapping of bars should preferably be done at:

Q52. Which property of concrete is assessed by the compaction factor test?

Q53. In RCC structures, which part is primarily subjected to tensile stresses?

Q54. What is the effect of excess water in concrete?

Q55. The maximum size of aggregate for RCC work, as per IS 456:2000, should generally be:

Q56. The main reinforcement in a one-way slab runs:

Q57. Which admixture is used to delay the setting time of concrete?

Q58. The ratio of span to depth for cantilever RCC slabs should not exceed:

Q59. The moment of resistance of an RCC section depends upon:

Q60. Which type of RCC beam carries axial load as well as bending moment?

Q61. The ideal shape for RCC columns is:

Q62. The commonly used method for curing concrete slabs is:

Q63. The slump value for concrete used in beams and slabs should ideally be:

Q64. Tensile cracks in RCC beams first appear at:

Q65. Maximum number of bars in a layer for a slab should be:

Q66. What is the primary reason for providing stirrups in RCC beams?

Q67. What is the minimum grade of concrete recommended for RCC structures exposed to severe environmental conditions?

Q68. Which IS code specifies the mix design procedure for concrete?

Q69. What is the effective cover in RCC?

Q70. In RCC columns, which reinforcement is provided to prevent buckling?

Q71. What is the usual minimum diameter for main bars in RCC beams?

Q72. A beam is considered over-reinforced if:

Q73. Which aggregate property affects concrete workability the most?

Q74. Which test assesses the flexural strength of concrete?

Q75. To improve durability, the water-cement ratio for RCC should generally be:

Q76. Which test determines the soundness of cement?

Q77. Which property of concrete is measured using a slump test?

Q78. In RCC, the cover to reinforcement is provided primarily to:

Q79. Which cement is preferred for marine structures?

Q80. The function of lateral ties in RCC columns is to:

Q81. Minimum clear cover for main reinforcement in RCC slabs should be:

Q82. Which of the following increases concrete workability?

Q83. Curing of concrete is necessary to:

Q84. Which type of stress is resisted effectively by concrete?

Q85. The maximum spacing of stirrups in RCC beams should not exceed:

Q86. In RCC beams, which reinforcement resists bending tension?

Q87. The minimum clear spacing between two parallel reinforcing bars should be:

Q88. Which of these factors affects the shrinkage of concrete the most?

Q89. The maximum permissible deflection for RCC beams as per IS 456 is:

Q90. Which factor directly affects the durability of concrete?

Q91. Which of the following is NOT a function of concrete cover?

Q92. The purpose of hooks at the ends of stirrups is to:

Q93. In RCC columns, minimum number of longitudinal bars for circular section is:

Q94. Lapping of reinforcement bars is avoided in:

Q95. Reinforced Cement Concrete was first used by:

Section 22) Reinforced Cement Concrete (RCC) Design

📖 Limit State of Collapse: Flexure (IS 456:2000, Annex G)

Depth of Neutral Axis (Actual)

$$ x_u = \frac{0.87 f_y A_st}{0.36 f_ck b} $$

Where:
\( x_u \) = Depth of neutral axis (mm)
\( f_y \) = Characteristic strength of steel (N/mm²)
\( A_st \) = Area of tension reinforcement (mm²)
\( f_ck \) = Characteristic compressive strength of concrete (N/mm²)
\( b \) = Width of the beam section (mm)

Limiting Depth of Neutral Axis (\( x_{u,max} \))

$$ x_{u,max} = \begin{cases} 0.53 \, d & \text{for Fe 415} \\ 0.48 \, d & \text{for Fe 500} \\ 0.46 \, d & \text{for Fe 550} \end{cases} $$

Where:
\( d \) = Effective depth of beam (mm)

Ultimate Moment of Resistance (\( M_u \))

$$ M_u = 0.36 f_ck b x_u \left( d - 0.42 x_u \right) $$

For balanced section (\( x_u = x_{u,max} \)):

$$ M_{u,lim} = 0.36 f_ck b x_{u,max} \left( d - 0.42 x_{u,max} \right) $$

📖 Limit State of Collapse: Shear (IS 456:2000, Clause 40)

Nominal Shear Stress

$$ \tau_v = \frac{V_u}{b d} $$

Where:
\( V_u \) = Factored shear force (N)
\( \tau_v \) = Nominal shear stress (N/mm²)

Shear Resistance of Concrete (\( \tau_c \))

Depending on percentage of tension reinforcement (\( p_t = \frac{100 A_st}{b d} \)) and grade of concrete, obtained from IS 456 Table 19.

Shear Reinforcement (Vertical Stirrups)

$$ V_{us} = \frac{0.87 f_y A_{sv} d}{s_v} $$

Where:
\( V_{us} \) = Shear strength to be resisted by stirrups (\( V_u - \tau_c b d \))
\( A_{sv} \) = Total cross-sectional area of stirrup legs (mm²)
\( s_v \) = Spacing of stirrups along the span (mm)

📖 Development Length & Bond (IS 456:2000, Clause 26.2.1)

Development Length (\( L_d \))

$$ L_d = \frac{\phi \sigma_s}{4 \tau_{bd}} = \frac{0.87 f_y \phi}{4 \tau_{bd}} $$

Where:
\( \phi \) = Nominal diameter of reinforcing bar (mm)
\( \tau_{bd} \) = Design bond stress (N/mm², increased by 60% for deformed bars in tension)

📖 Compression Members / Columns (IS 456:2000, Clause 39)

Ultimate Axial Load Capacity of Short Axially Loaded Column

$$ P_u = 0.4 f_ck A_c + 0.67 f_y A_sc $$

Where:
\( P_u \) = Ultimate axial load on column (N)
\( A_c \) = Net area of concrete section (\( A_g - A_sc \)) (mm²)
\( A_g \) = Gross area of column section (mm²)
\( A_sc \) = Area of longitudinal steel reinforcement (mm²)

📖 Deflection Control: Span-to-Depth Ratios (IS 456:2000, Clause 23.2.1)

Basic Span / Effective Depth Ratio

$$ \left(\frac{L}{d}\right)_{basic} = \begin{cases} 7 & \text{for Cantilever} \\ 20 & \text{for Simply Supported} \\ 26 & \text{for Continuous} \end{cases} $$

Modified by multiplying with modification factor based on tension reinforcement (\( F_t \)) and compression reinforcement (\( F_c \)).

📖 Minimum Concrete Grade, Cover & Durability (IS 456:2000)

Minimum grade for RCC structural members: M20 (Clause 6.1.1 / Table 5 notes).

Nominal cover to all reinforcement (Table 16) – selected values:

  • Slabs: 20 mm (mild exposure) – may increase for severe exposure
  • Beams / columns: 30 mm (mild) / 40–50 mm (severe / very severe)
  • Footings: 50 mm (minimum clear cover to main reinforcement)

Cover protects steel from corrosion and fire and ensures bond. Cover blocks maintain the specified thickness during casting.

Water–cement ratio is the dominant factor controlling durability and shrinkage. For durable RCC, free w/c is generally kept ≤ 0.45 (severe exposure may require lower values). Higher w/c increases porosity, permeability and drying shrinkage.

📖 Partial Safety Factors & Modular Ratio
ItemValue (Limit State of Collapse)
Concrete (\(\gamma_c\))1.5
Steel (\(\gamma_s\))1.15

Modular ratio (working-stress method)

$$ m = \frac{E_s}{E_c} = \frac{280}{3\sigma_{cbc}} $$

where \(\sigma_{cbc}\) is the permissible compressive stress in concrete (N/mm²).

Permissible tensile stress (WSM) for Fe 250: 140 N/mm² in half the depth of slab / 230? – commonly taken as 140 N/mm² for tension up to half the depth of member in some tables; IS 456 Table 22 gives 140 N/mm² for Fe 250 in tension (half). Many textbooks list 140 N/mm² for Fe 250 tension; the MCQ answer of 215 N/mm² corresponds to the older IS value sometimes quoted for Fe 250 in pure tension – use the code table in force at the time of design.

📖 Assumptions of Limit State Design for Flexure
  • Plane sections remain plane after bending (Bernoulli).
  • Maximum compressive strain in concrete = 0.0035.
  • Tensile strength of concrete is ignored in flexure design.
  • Design stress–strain curve for concrete is the parabolic-rectangular idealisation of IS 456.
  • Design stress–strain curve for steel is as given in Fig. 23 of IS 456 (with partial safety factor 1.15).

Limit state of collapse deals with strength; limit state of serviceability deals with deflection, cracking and vibration.

📖 Singly vs Doubly Reinforced Beams

Singly reinforced – reinforcement only in the tension zone. Moment capacity limited by \(M_{u,lim}\) of the balanced section.

Doubly reinforced – additional compression steel when the required moment exceeds \(M_{u,lim}\). Compression steel helps the section resist the extra moment and also improves ductility and deflection control.

Main (longitudinal) bars resist bending tension; in a simply supported beam they are placed in the bottom zone.

📖 Shear Reinforcement (Stirrups)

Stirrups resist shear and hold longitudinal bars in position. Vertical stirrups:

$$ V_{us} = \frac{0.87 f_y A_{sv} d}{s_v} $$

Maximum spacing of stirrups (Clause 26.5.1.5):

  • ≤ 0.75 d for vertical stirrups
  • ≤ 300 mm

Hooks at the ends of stirrups provide anchorage. Mild-steel plain bars are often preferred for stirrups because of better bendability, though HYSD/TMT are also used.

📖 Columns – Longitudinal Bars & Ties
  • Minimum number of longitudinal bars: 4 for rectangular / square, 6 for circular columns.
  • Lateral ties prevent buckling of longitudinal bars and confine the concrete core.
  • Pitch of ties ≤ least lateral dimension, ≤ 16 × smallest longitudinal bar diameter, ≤ 300 mm.

Short axially loaded column capacity (already given above):

$$ P_u = 0.4 f_{ck} A_c + 0.67 f_y A_{sc} $$

📖 Development Length, Lap & Spacing

Development length

$$ L_d = \frac{\phi \sigma_s}{4 \tau_{bd}} \approx \frac{0.87 f_y \phi}{4 \tau_{bd}} $$

Lap length in tension (Clause 26.2.5.1) – not less than \(L_d\) or 30\(\phi\); many exam keys quote 40\(\phi\) as a conservative minimum for tension laps. Laps should preferably be avoided in regions of high tension (mid-span of simply supported beams, etc.).

Minimum clear spacing between parallel bars ≥ diameter of larger bar, ≥ maximum aggregate size + 5 mm, ≥ 5 mm (Clause 26.3.2).

📖 Deflection Limits (Serviceability)

Final deflection including effects of temperature, creep and shrinkage ≤ span/250.

Deflection after erection of partitions / finishes ≤ span/350 or 20 mm (whichever is less).

Basic L/d ratios (cantilever 7, simply supported 20, continuous 26) are modified by factors for tension and compression steel.

📖 Tests on Cement & Concrete
  • Slump test – workability of fresh concrete.
  • Le-Chatelier test – soundness of cement (expansion due to free lime / magnesia).
  • Vicat apparatus – consistency and setting times of cement.
  • Flexural / beam test – modulus of rupture (flexural strength) of concrete.
📖 Special Cements & Practice Notes
  • Sulphate-resisting cement – preferred for marine structures and sulphate-bearing soils.
  • Curing is essential for strength gain, control of temperature gradients and reduction of plastic / drying shrinkage.
  • Admixtures (plasticisers / superplasticisers) improve workability without increasing water content.
  • Joseph Monier is credited with early practical use of reinforced concrete (1867).
Yogendra Gopal Borse

Yogendra Gopal Borse

Civil Engineer | Assistant Engineer Grade-I, Maharashtra PWD

B.Tech (Civil) from VJTI Mumbai. Experienced in bridge design, road works, estimation, project monitoring and digital engineering tools. Creator of YogiPWD – practical technical resources for civil engineers.

Read full About →