MCQ Irrigation Engineering
Q1. The duty of water is defined as:
Q2. The base period is:
Q3. Kor watering refers to:
Q4. Canal outlets are also known as:
Q5. Delta of a crop is the:
Q6. A cross regulator is used in a canal system to:
Q7. A gravity dam resists external forces mainly by:
Q8. The ratio of velocity head to pressure head in a Venturi flume is:
Q9. A canal fall is provided to:
Q10. Which of the following irrigation methods is best suited for saline soils?
Q11. The most suitable dam for a narrow deep gorge is:
Q12. The correct relation for duty (D), delta (Δ), and base period (B) is:
Q13. The major cause of waterlogging in command areas is:
Q14. A canal aligned at right angles to contour lines is called:
Q15. The best method of irrigation for row crops like sugarcane is:
Q16. The process of applying water by breaking it into droplets is known as:
Q17. The water required for raising a crop is known as:
Q18. The outlet which maintains a constant discharge irrespective of canal fluctuations is:
Q19. An ogee spillway is suitable for:
Q20. The irrigation efficiency for surface irrigation systems is typically:
Q21. The ratio of gross commanded area (GCA) to cultural commanded area (CCA) is called:
Q22. The hydrograph represents:
Q23. The canal alignment laid parallel to contours is known as:
Q24. The structure used to dispose excess water from a reservoir is:
Q25. For estimating peak flood discharge for a small catchment, the most suitable method is:
Q26. Evapotranspiration includes:
Q27. The best soil for constructing an earthen dam is:
Q28. Which type of canal is preferred for controlling waterlogging?
Q29. The discharge through a fully submerged orifice is proportional to:
Q30. An irrigation outlet providing a fixed discharge independent of water levels is called:
Q31. The main function of a canal fall is to:
Q32. The most effective method of irrigation for water-scarce areas is:
Q33. The ratio of average depth of water stored to the depth of water lost due to evaporation and seepage in a reservoir is:
Q34. A diversion headworks built across a river serves to:
Q35. The unit of irrigation delta is:
Q36. The rate at which water is supplied to the crops is called:
Q37. The most efficient surface irrigation method is:
Q38. The ratio of water stored in the root zone to water applied at the field is:
Q39. Which one is not a type of cross drainage work?
Q40. The unit of measurement for duty is:
Q41. A cross regulator in a canal system is used to:
Q42. The method of supplying water to crops by lifting from a well using buckets is called:
Q43. The average annual rainfall over India is about:
Q44. The permissible velocity of flow in earthen channels is limited to avoid:
Q45. The factor accounting for water losses during conveyance is:
Q46. Which dam type is most suitable for narrow gorges with sound rock foundations?
Q47. The relationship between duty (D), delta (Δ) and base period (B) is:
Q48. The gross command area is:
Q49. The stream gauging method suitable for turbulent mountain streams is:
Q50. An irrigation outlet discharging water proportional to the distributary discharge is:
Q51. A syphon aqueduct is preferred when:
Q52. The water allowance for a crop depends mainly upon:
Q53. The water requirement for a paddy crop is generally:
Q54. Canal escapes are structures built to:
Q55. The term ‘Kor period’ in irrigation denotes:
Q56. The sediment removal structure on a canal head regulator is called:
Q57. The main cause of waterlogging is:
Q58. The most suitable canal lining material for high seepage soils is:
Q59. The useful storage capacity of a reservoir is the volume between:
Q60. In lift irrigation systems, water is raised using:
Q61. The main objective of providing a canal fall is to:
Q62. Which one is a non-modular outlet?
Q63. The correct formula for calculating delta (Δ) in cm is:
Q64. In cross drainage works, a super passage is where:
Q65. In which irrigation method is water applied below the soil surface?
Q66. The duty of water is generally expressed in:
Q67. The outlet discharging fixed discharge irrespective of canal water levels is called:
Q68. Sprinkler irrigation is most suitable for:
Q69. The command area where irrigation is assured in all seasons is called:
Q70. In canal irrigation, the most significant type of water loss is by:
Q71. The ratio of the area irrigated in a base period to the base period itself is called:
Q72. Which type of cross-drainage work is provided when the canal is carried over the drain?
Q73. Permanent water-logging can be effectively controlled by:
Q74. The term ‘time factor’ in water management is associated with:
Q75. The method of irrigation most suitable for uneven terrain is:
Q76. When canal and drain cross each other at the same level, which structure is used?
Q77. For paddy crop, the kor period generally occurs:
Q78. Which one of these methods provides water directly to the root zone?
Q79. The depth of water supplied to a crop per base period is called:
Q80. The ratio of dead storage to gross storage in a reservoir is usually:
Q81. The structure provided to dispose surplus water from a reservoir is called:
Q82. Which of the following irrigation methods achieves highest application efficiency?
Q83. Which of the following is a controlled cross drainage work?
Q84. An irrigation outlet with proportional discharge to water level in the distributary is:
Q85. Which device measures discharge by flow constriction and head measurement?
Q86. The ratio of the depth of water to the depth of root zone is known as:
Q87. The ratio of total irrigated area to cultivable commanded area is called:
Q88. Which parameter is not used while designing an aqueduct?
Q89. The portion of reservoir capacity that can’t be used under normal conditions is:
Q90. What is the main cause of waterlogging in canal irrigated areas?
Q91. In a storage reservoir, the difference between gross storage and dead storage is:
Q92. The outlet in a canal that is not affected by water levels in both canal and watercourse is:
Q93. The curve plotted between discharge and time at a point on a stream is called:
Q94. The crest level of a canal escape is kept:
Q95. Which factor affects the duty of water most?
Q96. A river training work used to confine flow within a definite channel is:
Q97. Gravity dams are most suitable for:
Q98. A ‘paddy field’ typically requires:
Q99. Which of the following is a non-modular outlet?
Q100. A weir constructed to raise water level for diversion into canal is:
Irrigation Engineering
Relation Between Duty, Delta, and Base Period
$$ \Delta = \frac{8.64 B}{D} $$
Where:
\( \Delta \) = Total depth of water (hectare-meters / hectare or meters)
\( B \) = Base period (days)
\( D \) = Duty of water (hectares/cumec)
Net Irrigation Requirement (NIR)
$$ NIR = CU - P_e $$
Where:
\( CU \) = Consumptive use (Evapotranspiration)
\( P_e \) = Effective rainfall
Gross Irrigation Requirement (GIR)
$$ GIR = \frac{NIR}{\eta_a} $$
Where:
\( \eta_a \) = Water application efficiency (fraction)
Field Irrigation Requirement (FIR) & Capacity Efficiencies
$$ FIR = \frac{NIR}{\text{Field Efficiency}} $$
$$ \eta_s = \frac{W_s}{W_n} \times 100 $$
Where:
\( \eta_s \) = Water storage efficiency
\( W_s \) = Water stored in root zone during irrigation
\( W_n \) = Water needed in root zone prior to irrigation
Critical Velocity Formula
$$ V_0 = 0.546 \cdot y^{0.64} $$
Where:
\( V_0 \) = Critical velocity (m/s)
\( y \) = Full supply depth of channel (m)
Critical Velocity Ratio (CVR / m)
$$ m = \frac{V}{V_0} $$
Where:
\( V \) = Actual mean velocity of flow (m/s)
Silt Factor
$$ f = 1.76 \sqrt{d_m} $$
Where:
\( d_m \) = Mean particle size of silt (mm)
Lacey’s Regime Equations
$$ V = \left( \frac{Q f^2}{140} \right)^{1/6} $$
$$ P = 2.67 \sqrt{Q} $$
$$ R = \frac{5}{2} \left( \frac{V^2}{f} \right) $$
$$ S = \frac{f^{5/3}}{3340 \cdot Q^{1/6}} $$
Where:
\( Q \) = Discharge (m³/s)
\( P \) = Wetted perimeter (m)
\( R \) = Hydraulic radius (m)
\( S \) = Bed slope of channel
Bligh’s Creep Theory (Total Creep Length)
$$ L = c \cdot H $$
Where:
\( L \) = Total length of creep
\( c \) = Bligh’s coefficient of creep
\( H \) = Total head/seepage head
Khosla’s Theory: Exit Gradient
$$ G_e = \frac{H}{\pi \cdot d} \cdot \frac{1}{\sqrt{\lambda}} $$
$$ \lambda = \frac{1 + \sqrt{1 + \alpha^2}}{2}, \quad \alpha = \frac{B}{d} $$
Where:
\( G_e \) = Exit gradient
\( H \) = Maximum static head (m)
\( d \) = Depth of downstream cutoff/pile (m)
\( B \) = Total length of floor (m)
Sodium Adsorption Ratio (SAR)
$$ SAR = \frac{\text{Na}^+}{\sqrt{\frac{\text{Ca}^{2+} + \text{Mg}^{2+}}{2}}} $$
Where:
Ion concentrations are expressed in milliequivalents per liter (meq/L).
Duty (D) – Area that can be irrigated by a unit discharge of 1 cumec continuously during the base period. Units: hectares/cumec.
Delta (Δ) – Total depth of water required by a crop over its base period. Units: cm or m.
Base period (B) – Number of days between the first watering of a crop at the time of sowing and the last watering before harvesting (period of irrigation demand).
Crop period – Total time from sowing to harvesting (may be slightly longer than base period).
Kor watering – First watering after sowing, essential for germination; kor period is the critical early stage when demand is highest (especially for paddy).
Consumptive use (CU) – Water lost by a crop through evapotranspiration; approximately equal to the irrigation requirement when effective rainfall is subtracted.
Fundamental relation
$$ \Delta = \frac{8.64\,B}{D} $$
(Δ in metres, B in days, D in ha/cumec; or adjust constant if Δ is in cm.)
- Gross Commanded Area (GCA) – Total area that can theoretically be irrigated from a canal system.
- Culturable Commanded Area (CCA) – Portion of GCA that is cultivable.
- Intensity of irrigation – (Area irrigated in a season / CCA) × 100 %.
- Crop ratio – Ratio of areas under different crops (sometimes also loosely used for GCA/CCA relationships).
| Method | Best suited for | Typical application efficiency |
|---|---|---|
| Furrow | Row crops (sugarcane, maize, cotton) | 50–70 % |
| Border / check-basin | Close-growing crops, level land | 40–60 % |
| Flood / free flooding | Paddy fields | 30–50 % |
| Sprinkler | Uneven terrain, light soils | 60–80 % |
| Drip | Water-scarce areas, saline soils, orchards, vegetables | 80–95 % |
| Subsurface | Direct root-zone supply | High |
Drip irrigation is preferred for saline soils and highest application efficiency because water is delivered at the root zone with minimal evaporation and deep percolation.
- Non-modular – Discharge depends on water levels in both parent channel and watercourse (e.g., open flume, simple pipe outlet).
- Semi-modular (flexible) – Discharge independent of water level in the watercourse but depends on level in the parent channel (e.g., Kennedy’s gauge outlet, open flume with free fall).
- Modular – Discharge independent of water levels in both channels (e.g., Gibb’s module, Venturi meter type).
Modular outlets give constant discharge irrespective of fluctuations; they are also called modules.
- Ridge (watershed) canal – Aligned along a ridge; can irrigate both sides; roughly perpendicular to contours.
- Contour canal – Follows a contour; irrigates only one side; needs cross-drainage works frequently.
- Side-slope canal – Aligned roughly parallel to the ground slope, between ridge and valley.
Lined canals reduce seepage, control waterlogging and allow steeper slopes / higher velocities.
- Canal fall – Provides a controlled drop in bed level when ground slope is steeper than the designed canal slope.
- Cross regulator – Located across the parent channel; maintains upstream water level and controls distribution into offtakes.
- Head regulator – Controls discharge into a branch or distributary.
- Escape – Disposes of surplus canal water; crest usually set at or near full supply level (FSL).
- Diversion headworks / diversion weir – Raises river water level so that it can be diverted into a canal.
| Structure | Relative levels | Description |
|---|---|---|
| Aqueduct | Canal above drain | Canal is carried over the natural drain in a trough. |
| Syphon aqueduct | Canal above drain (drain under pressure) | Drain flows under the canal under pressure. |
| Super passage | Drain above canal | Natural drain is carried over the canal. |
| Canal syphon | Canal under drain | Canal flows under the drain under pressure. |
| Level crossing | Same level | Both canal and drain are at the same level; controlled by gates. |
- Gravity dam – Resists water force mainly by its own weight; suitable for wide valleys with sound rock foundation.
- Arch dam – Transfers load to abutments by arch action; ideal for narrow deep gorges with strong abutments.
- Earth / rockfill dam – Embankment dams; require suitable soils (silty clay preferred for core) and large foundation area.
- Ogee spillway – Overflow spillway shaped to the underside of the nappe; common on gravity dams.
- Spillway – Structure that safely passes surplus reservoir water downstream.
Reservoir storage terms
- Dead storage – Volume below the lowest outlet; not usable under normal operation (typically 10–25 % of gross storage).
- Live (useful) storage – Gross storage − dead storage.
- Gross storage – Total volume up to full reservoir level.
Main causes of waterlogging in canal-commanded areas:
- Seepage from unlined canals
- Over-irrigation
- Inadequate surface or subsurface drainage
- Presence of impermeable layers
Control measures: lining of canals, subsurface (tile) drainage, surface drains, conjunctive use of surface and groundwater, controlled irrigation scheduling.
Venturi flume – Constriction that produces a measurable head difference; discharge is related to the square root of the head difference. Useful in canals because it has low head loss and is self-cleaning.
Submerged orifice
$$ Q = C_d A \sqrt{2gH} \quad \Rightarrow \quad Q \propto \sqrt{H} $$
where \(H\) is the difference in water levels on the upstream and downstream sides.
- Guide banks – Confines the river to a definite channel through a bridge or barrage and protects the approaches.
- Spurs / groynes – Project from the bank into the river to deflect current and protect the bank.
$$ Q = \frac{1}{360}\,C\,I\,A \quad \text{(metric form often written as } Q = 0.00278\,C\,I\,A\text{)} $$
where \(Q\) is peak runoff (m³/s), \(C\) runoff coefficient, \(I\) rainfall intensity (mm/h) for duration equal to time of concentration, \(A\) catchment area (ha). Preferred for small catchments.
0 Comments
If you have any doubts, suggestions , corrections etc. let me know